Hi,
We’ve successfully developed our first few custom development boards based on the nRF54H20 MCU, using the Fanstel BM20C module. However, we've discovered that the module...
Hello Nordic,
I am looking for a sample or instruction (step by step) for custom bootloader.
Our application code is ready and all the left thing is BLE DFU and custom...
Hey All
Im working on a new product and its the first time I'm developing around the nrf5340, I'm looking for some guidance around the supply configuration for maximum...
Hi Team,
We are using nRF9160 MQTT sample code 'mqtt_simple'.
1. What is the maximum payload we can send in one single PUBLISH?
2. I want to send 4KB of data in single...
I am getteing a -12 error when trying to access a open/create a file using littlefs and a fs_open command on a nrf5340 custom board.
The filesystem seems to be mounted fine...
hi support team,
i am testing SLM demo.
i tried command as below:
[16:24:30.475] AT%XSYSTEMMODE=0,0,1,0
[16:24:30.496]
[16:24:30.496] OK
[16:24:30.496]
[16:24...
I have a preset stored in CMakePresets.json:
When I go to create a new build configuration with the preset, the extension creates an Extra CMake Arguments row with:
...
Hi,
I want to reduce the current both in the TX mode
and in the system on idle mode as much as possible.
I measured the current consumption of nRF52DK with the original...
With s132 v3, in addition to configuring the GATT to receive larger packets like so:
ble_enable_params.gatt_enable_params.att_mtu = 247;
err_code = softdevice_enable...
Hi all,
I'm working on secure bootloader on sdk12.2.0, And Installed nrfutil v2.3.0 by following the user guide nrfutil v1.2 successfully and it working well without any...
Hi everyone,
I'm using SDK 12.2 on nRF51822. Trying to get the buttonless dfu app example to work.
Here's what I do:
Compile buttonless dfu app.
Generate settings...
Hi,
I'm new to python and also the NRF51 dongle. I need to build a python script to connect my NRF51 dongle to a BLE device without using Master Control Panel. I tried using...
Hello,
i a have a problem debugging application with bootloader installed. I work with GCC for the application.
What is happening is the following:
If i program application...
Hi,
i used the SPIM example to create a connection with my ads1256. on my breadboard it worked properly. now i switched to a layouted board and every SPI pin is working...
Hi all,
I am using a J link to program a NRF52 via keil. It is successful but, every second program it fails with a Flash timeout error.
I am programming the application...
Hi,
I am trying to secure DFU on SDK 11 (NRF52). Would you please suggest if there is a way to secure firmware on old sdk, without upgrading to sdk 12+?
Thanks.
Hi All,
At the moment, I have three nodes and would like to configure one node as an end-device and the other two as routers. Using CoAP, the simple_coap_server is used...
I am migrating from nrf51 to nrf52. Using SDK12.1
On NRF51, I used the PWM Library to use 2 buttons on the DK to dim up or down onboard LED1 (called OUTPUT_LED).
It worked...
We are attempting to perform an OTA and as such want to transfer a large amount of data as quickly as possible.
When I attempt to transfer the data with connection intervals...
Dear Nordic team,
We have been working with SDK 8 and Softdevice S110 so far. We would now like to have the DFU using OTA for our product. I am looking for SDK versions...
Hallo Community,
I am new with Nordic chips, now Im trying to develop a BLE central, then i took the BLE_CENTRAL BLE_APP_UART example to start doing it, the SDK is the...
hello,i am using nrf52 DK.I was testing ADC example code .I am giving acq time is 3microsec .I want to find the total time is taken to sample adc for one sec.In data sheet...
