Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
Condition: nRF52, SDK11,s132, SDS v2.0.
Using the sd_ble_gatts_hvx() in timer1 interrupt service(timer1 interrupt priority is set to level 3) will result in hardfault. While...
I am using SDK_11 s130. I am looking at app_error_fault_handler() in app_error_weak.c
Inside app_error_fault_handler(), there is this line of code;
UNUSED_VARIABLE(bsp_indication_set...
Hi,
I am using keil uvision 5.17, SD 130, nRF 51822, dualbank bootloader.
I have programmed own application and merged bootloader, application, soft device.
I...
I am using ble_app_gls on SDK_11 s130 on nRF51-dk.
This is a follow-up question to the question below.
devzone.nordicsemi.com/.../
After enabling debugging, I discovered...
Hi,
I'm using the example projects "ble_peripheral/ble_app_uart" "ble_central/ble_app_uart_c" in SDK10.0.0 to test data throughput.
I'm sending 20bytes of payload. But...
Hi,
I am using nrfjprog package installed in folder /opt/Nrfjprog. I am getting the fallowing error.
nrfjprog --eraseall
ERROR: JLinkARM.dll load failed. Try again...
Hi,
I've migrate from 3V to 1.8v power supply.
before the migration, using 3V power supply, DEC2 connected to 47nF directly to GND.
after the migration, using1.8V power...
in android program i disconnect from my gat with this code
while(isconnected){
mbluetoothGatt.disconnect();
Log.d(TAG, "Disconnecttodevice: ");
}
mbluetoothGatt...
Hello, I load UART over BLE example on nrf51DK (51422) DK board and measure for 13 seconds from power on.
Here is the result graph and the average current is about 175uAh...
Hello Nordic! In my FW, I need to know when a specific packet has been actually sent (because of SD packet buffering). I am able to receive the BLE_EVT_TX_COMPLETE event,...
Hello I'm using SDK nRF5_SDK_11.0.0_89a8197.zip and I find out that most freeRTOS file version is: "FreeRTOS V8.2.1" but "external\freertos\config\FreeRTOSConfig.h" is in...
Hello,
I am trying to configure my NRF52 dev kit (PCA 10040) to work with pwm using the build-in timer. I used some code from the low_power_pwm example but when I am using...
I am working in a project.The project had defined the manuf_data that it didn't need the company_identifier(bluetooth core 4.0). Is there any way does not show company_identifier...
Hi,
This is a request for all the users to post some details of sensors they are using along with Nordic chips. We will get familiar with 10 most popular sensors that are...
