I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
Is there any software I2c library or example projects for nRF52 devices (PCA10400) with pin configuration, read and write functions? I am using an SMBus based sensor...
Hello,
I am testing the ble_peripheral example of ble_app_uart (SDK 12, soft device 130), this has been asked at a lot of places that the MTU is limited to 20.
But then...
Hi,
I am using nRF51822 and implemented timer-2 with 2 sec capture/compare interrupt rate. But if I want to read timer's current count before it generates interrupt or...
at nRF51 SDK v9.0.0, S130, PCA10040, at peripheral side
If we receive a characteristics less than 20 bytes, we can get the correct handle value(like 0x3B). And then everything...
I bought nRF51-DK yesterday.
I installed nRFgo Studio(1.20), Keil uVision(5.15), Softdevice s110 (8.0.0), J-Link(5.00),
nRF51 MDK(7.2.1)
I turned on the nRFgo studio...
Hi,
I'm using Eclipse Mars 5.2 on Windows 10 along with the GNU Toolchain as described in the "Development with GCC and Eclipse Tutorial" by Vidar Berg (Thanks very much...
Hi, I can't get SPI slave mode working on nRF51822. I'm using the Core51822 module with a BLE400 board from Waveshare and up to date mbed. SPISlave::receive() always returns...
I implement it with sdk 11.0 and a third party core-board.Firstly,I program s132_nrf52_2.0.1 SoftDevice by nRFgo Studio,then I open ble_app_hrs s132_with_dfu(arm4) project...
Hi,
Currently I'm using internal RC osciallator for LFCLK on the system that run on CMSIS-RTX and Softdevice S110 and it doesn't have external 32K crystal.
The RTC os...
Hello,
I just received an NRF52DK today. I was able to run the demo (LED blink/Switch and NFC) which comes factory installed. But copying the hex files from demo (proximity...
In the picture, the usb pcb is PCA10000, the circle PCB is the product PCB.
The diameter is 20mm.
Chip antenna is used now but the distance is 5m in 4dbm TX.
Here...
Hi all,
I would like to design a product based on the nRF52832 chip. The board should have an accelerometer, a charging circuitry for a LiPo and some additional components...
Hi there,
I am done with TI and the new IDE and Stack 2.2
May be anybody can point me to the right IDE and chip to replace my TI CC2640 4x4 designs to Nordic semiconductor...
