I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
Hi!,
I'm working in a Android app to communicate with a nRF52/nRF51 boards.
I've been using Bluetooth Smart nRF51822 Beacon Kit.
But I think what I need is not possible...
How do I change the properties of the Generic Access service's "Device Name" characteristic to be Read Only, not Read and Write? I see this
BLE_GAP_CONN_SEC_MODE_SET_OPEN...
Hi,
We are sending data every connection interval which is a stream using the API sd_ble_gattc_write. Whenever there is a dropped packet from what we understand, the Softdevice...
I used SDK11, SD332, and no change anything.
the application reset as picture.
can you test this issue and give suggest ,why app reset?
D:\work\nordic\BLE\SDK\nRF5_SDK_11...
I need a code example (e.g. Health Thermometer) that runs on the Beacon Kit. I have tried several combinations of soft devices and code examples, but I can't get it running...
Hello,
I started implementing a project with the device manager. I am using the S120 as central.
I am able to connect to 3 peripherals at the same time (also nordic nrf51822...
Hi,
The environment is Ubuntu 16.04 running on parallels on a mac pro.
I am following all the installation instructions and I get no errors, except that the opus driver...
Hi,
Today, i try to use the UART SERVICE from nordic on both smartphone and NRF51.
I succeed to send data between the two.
But now, i want to send data longer than 20...
Hi,
Using SDK12.1 with nrf52. Have SD and bootloader on the device and trying to load application via BLE DFU.
It randomly gets stuck. (see attached screenshot)
And...
Hello,
I have some trouble to use the Secure Bootloader example, which comes with the
nRF5_SDK_12.1.0
I installed the latest nrfutil and hexmerge. I can compile the...
This piece of code appears in all IoT SDK examples:
eui48_t ipv6_medium_eui48;
err_code = ipv6_medium_eui48_get(m_ipv6_medium.ipv6_medium_instance_id,
&ipv6_medium_eui48...
Hi, I am using the nrf uart app to communicate with a smart phone and the NRF52. I am trying to detect whenever it is sent a value between 0 and 60 from the phone, and save...
Hi,
I'm working on nRF51822 with SDK 11.0.0 softdevice s130
I have an nRF module acting as central and smartphones (iOS and Android) acting as peripheral.
I tested...
Hello, what is the BLE max range w/out usin PCB antenna?
And what range ll be if i reducing the connection interval down to the minimum 7.5ms, set Tx power to +4dBm using...
I am using the nrf51822-QFAC-R in an application where the realization of the antenna is very challenging, and I expect to have an antenna |S11|=-1dB, with variations of the...
