Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hello, I'm trying to generate DFU keys with the nrfutil.exe tool from Master Control Panel 3.10.0.
I always get errors....
C:\Program Files (x86)\Nordic Semiconductor...
Hi,
nrf51822 device obverse six bytes mac addres could change，when OTA failed.
six bytes mac address, five bytes fixed, one byte can change when OTA failed.
Now，my app...
Hello,
I am using Nordic Nur-10W develop kit, trying to compile NurApiExample in Raspberry Pi. I wrote a Makefile, and complie process was OK. However, undefined reference...
hi
im using sdk v6 and when i turn my board on it goes to bootloader and i can upload my program into it .
the problem is that i want it to run to my main program after...
Hello,
I would like to use a custom flash memory layout for the flash memory of nrf52:
I thought that I should be able to use the UICR.NRFFW[0] - if I set to the start...
Hi, I use PCA10040 v1.1 with SDK12.1 via S132 v3.
I use Keil 5.21.
After testing the LBS example, I was merging the NUS (NORDIC UART Service) to the standalone LBS example...
I am working with nrf51822 board softdevice of s130,sdk11.0 version.I want to create 4 KB of Flash through PStorage.I am able to create 1 kb(maximum block size ) of flash...
Hello everyone,
I'm doing some work in SDK 12.1 and noticed that even the example peripheral project "ble_app_template" compiles to 26K under Keil. Given there is a 32K...
Iam using SDK10.0 and Softdevice version S110, i use device manager to monitor connections, i have implemented passkey pairing. nRF board is peripheral and iam connecting...
I have a project using printf to send AT commands to a cellular modem. It works well.
Yesterday I added Segger_RTT into the project.
With NRF_LOG_USES_RTT=0 defined.
...
I'm trying to get an a recognized ble pulse without using a softdevice. I started with the basic transmitter application and am trying to decipher the order for the data I...
Hello,
I am trying to get my device (nrf52832) to do DFU OTA, and to do so I am programming the bootloader before programming the s132 softdevice and the application. However...
Dear Colleagues,
I am much obliged for your kind assistance to me.
My Question:
I have setup my NRF8001 successfully (please find the setup file generate by the nrfgo...
Hi,
I use SPI Master driver to communicate with a flash memory.
I use SDK 12 and i use nrf_drv_spi_transfer(...); to write and read over SPI.
My problem is the following...
