Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I have an issue with my keyboard working with the windows suface (on windows 8.1). Occasionally, the last character sent is repeated several times instead of one. I do not...
On the nRF51822, I see that by programming the readback protect register, one can prevent reading code regions 0 and 1 from the SWD interface. However, if one had access to...
Hi,
I just watched a webinar from the bluetooth SIG on how to create source code from the nRFgo Studio for the nRF8001. Is the same possible for the nRF51822? To create...
Hi,
We modified the ble_app_hrs code to work with accelerometer peripheral, and we have created some custom characteristics with custom uuid's. Now we need to set the device...
Hello, Everyone:)
Nice to meet you !
Please could you commennt my first question on this community zone.
I've a question for the accuracy of synthesized clodk 32k on...
Hi
i am using NRf51822 custom board. In that i have NOR(spi0) and LED(i2c0).
But switching from spi0 to i2c0 is not possible so that i am not able to switch
off led...
Hello,
I'm using nRF51822 to implement a proprietary radio protocol. My first attempt, in the receiver, was polling the EVENTS_* registers. An example:
NRF_RADIO-...
I was trying to get access to the app_uart library, so I included app_uart.c in the "Source" folder; then added \Include\app_common and \Include\ble\softdevice in order to...
Hi,
We are using nrf51822 custom board.
i want to hard reboot of my device whenever gpio button is pressed for longer than 10 seconds.
i am using ble_app_hrs application...
from the product spec
NOTE: The 3 bit pipe information in the STATUS register is updated during the IRQ pin high to low
transition. The pipe information is unreliable if...
I'm load the UART example (pca10001) to the Evaluation Kit, i can see using hyperterminal the messages send by the kit ( the Start message) but after that i wont be able to...
Hi,
Is there any sample code which is using the sd_ecb_block_encrypt(); API, we are planning to do encryption and decryption of data, which will be transmitted and received...
Hi
1)In a nrf51822 ble app project, The board must have a external 32768Hz crystal,is that right?
or internal 32768Hz RC oscillator can instead of it?
2)when nrf51822 goes...
