I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I need to use sd_ble_gap_adv_data_set directly and pass custom advertising data, as I need to maximise space and not send the name etc
I have been using mbed which has...
\nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_uart\pca10028\s130\arm5_no_packs
I cannot find the define of pin6 pin17 pin21 pin 22 pin24
in this example ...
Hi. Can we develop and use our own firmware for any of the Nordic's beacon? Or do we need to mandatorily use firmware given by Nordic with beacon and modify them as much as...
I am using fds as my file system.
peer_manager is using file system too.
fds_register() is used to register callbacks. But how does the software know which callback is...
Hello
My nRF51 with S120 BLE stack is running as central. I want to connect 3 other nRF51 peripherals at the same time. So in the first step I did a scan and stored the...
Hi,
I'm developing an application based on the nRF52832 and I need a large throughput of over 100kbps, preferably over 200kbps.
I have managed to reach around 128kbps...
Hi
According to BT 4.2 Spec Vol 6, Part F, Section 3.2.9:-
" To write the entire value of an attribute larger than (ATT_MTU-3) octets, the prepare write request and...
hello,
i have a rather basic question concerning the design of the cycling power measurement value field.
how does a simple example for this value look like (variable...
What is the difference between SDK 8 and SDK 12 related to app_timer? I have used it like:
APP_TIMER_INIT(
APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS,
APP_TIMER_OP_QUEUE_SIZE...
Hi Nordic,
I have a star network with 3 nodes and 2 channels. I go through the whole pairing process and start sending data without problem. Now I want to, from the master...
I would like to advertise two different sets of data in parallel, such that one ADV packet is ongoing (say, A), and then I switch to the other packet (say, B) with different...
I tried to make android app for nrf51822 hrm proj.The app flows like this: scan--connect--discover service-- setnotification for every characteristic. The Hrm char was firstly...
Hello,
Could you please advise where I can download an older versions of nRFgo Studio that supports nRF24LU1P? I've got a USB dongle, which I need to re-program.
Thanks...
Hi
I use ble_app_hrs_rscs_relay example with sdk12
and when the APP_ADV_TIMEOUT_IN_SECONDS is reach the nrf52 stop advertising but the on_adv_evt has no BLE_ADV_EVT_IDLE...
Recently I had some strange bugs in few production devices. I inspected newer device markings and they look a bit different:
Pin 1 marking is square not circle.
Build...
