This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I am new to nRF ICs.
How to get 32.678KHz clock out from a pin? Is it possible? If yes, from which pin and how to configure it?
I am using 32.768KHZ external crystal fro...
I have designed several boards for the nRF51822-QFAA, namely with/for the Waveshare Core51822 module.
While one is working as expected - namely my "Orchid Lamp" (see links...
When softdevice S110 is used then bonding is not occuring (via nrf connect app to nrf51).but both devices get bonded when s130 is used?In Nrf connect app key matching failed...
Hi,
I have a working project where I use PWM driver with LEDs on the development board. I make use of the d52_starterkit.h where I have the following definitions:
#define...
Hi,
On a system reset, we want a mechanism to stay in bootloader for a short period before jumping in application. This way, if something is wrong in application that prevent...
Hi,
I am using ESB library for nRF52 microcontroller. At receiver i want to measure RSSI value of a packet. I got RRSI from nrf_esb_payload_t structure.
I am printing...
Hi,I have ibeacon (nRF51822) radioland-china.en.alibaba.com/.../long_range_300m_ibeacon_programable_nrf52822_beacons_bluetooth_4_0_tag_chip.html . I want to update the firmware...
Hi,
In my project i would like to save 100 bytes of information in RAM before going to System-off sleep mode.I have tested the example project given in sdk11 works okay.Have...
I am trying to read the battery level on a custom NRF52 board and I am getting a value that is around half of real voltage.
The same code works fine on NRF52 DK ( I was expecting...
I am looking at this example: github.com/.../main.c
In ble_evt_dispatch (line 315), this function forwards an BLE event to all of the modules. By looking at ble_evt_t,...
I am trying to build a BLE central application on the mbed compiler (target BLE Nano).
I have chosen the ble_app_uart_c example from the nRF5 SDK as a starting point. My...
Hi Support Team,
one error come out when use nrf connect, just as attached picture shows,
please help to check what cause this error,
no error come out on phone.
...
In reference to this issue in the Android DFU library...
github.com/.../33
... can someone from Nordic please explain how DFU OTA using the secure format on a device...
