Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi Nordic!
Long time short, I want to do an ANT application (S210, nRF51422) that pairs two slaves to one master. I have configured everything such that it pairs only when...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi Nordic,
We are trying to supply the chip nRF51422 with a Li-Ion battery. The nominal voltage is 3.7V, but as it is known, when full, this voltage can reach up to 4.2V...
Can the pc_ble_driver project located here be use in combination with SDK12?
We currently have it setup for SDK11 here, and want to upgrade to SDK12. We successfully built...
I want to develop a central role application (using a Redbear BLE Nano - based on nRF51)
I believe that this requires use of a softdevice and am looking for how to do this...
Hi. I am trying to set up timer in counter mode to count up signals from gpio through the ppi module, but it's not working. In main cycle I am testing the timer using led...
I want to sense bluetooth from any distance the radio can detect and without connecting, pairing or bonding. Simply turn led2 on while the nrf51822 senses RF and when it no...
For my application I need a lot of different timers. I dont use a soft device. Its a nRF52 Chip on board.
#define APP_TIMER_OP_QUEUE_SIZE 20
APP_TIMER_INIT(APP_TIMER_PRESCALER...
Experimental Buttonless DFU worked correctly when compiled with keil, but the same example compiled in eclipse by gcc is not switching to bootloader mode. value 0x01 is updated...
Hi There,
Are timers 3 & 4 accessible to the application when using the v3.0 S132 softstack on the NRF52?
Looking at table 4 of S132_SDS_v3.0.pdf they are not listed.
Cheers...
Hi Community, many thanks for reading!
I have built a Breadboardadapter for an ISP1302
Inside
On Breadboard
There is no Groundplane or design rules.
Yes,...
I am using a nrf8001 and the arduino aci library ported to work with my project.
I have started from hello world example.
Connecting to the device from android app, sending...
Hi there.
I am compiling the Nordic MQTT subscriber example (using TLS), and see the following error:
c:\program files (x86)\gnu tools arm embedded\5.4 2016q2\arm...
I have an example app ble_app_cscs_pca10028_s110 and when I add /../../../components/drivers_nrf/nrf_soc_nosd to User Include Directories I get an error NRF_EVT_FLASH_OPERATION_SUCCESS...
