Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi all, At present all my custom projects are running on sdk11.0.0 now I need signed bootloader for these I ported experimental signed bootloader from sdk10.0.0 to sdk11.0...
Dear friends,
I am having trouble connecting the Rigado BMD-300 with my Segger J-Link.
I am using the official breakout board from Rigado. I've connected all GND pins...
We are designing an additional "mbed-host board" that makes our nRF52832 based sensor board mbed-compatible ("Aistin Blue-2" board, see predecessor e.g. at www.kionix.com...
I use nrf51822 and soft device s130. I transmit some data using the printf function, and i need to clear the buffer before send data because sometimes i have noise in the...
Hi,
I'm new using XCode and I'm trying to use this guide:
github.com/.../documentation.md
I created a simple Cocoa Application, then I added iOSDFULibrary.framework...
Hello,
I'm experiencing a hardware fault followed by a reset when running the nRF5_SDK_12.1.0_0d23e2a ble_app_hrs_freertos with the following configuration :
PCA10040...
I'm using interrupts on nRF for the first time and have some trouble wrapping my head around / struggling with uncertainty in how to use the interrupts/GPIOTE efficiently...
Hi,
the system that i designed based on nRF51822 have two mode :
the first mode is the normal mode where the nrf should have a high connection interval of 2 to 3 seconds...
Hi,
I need to have a custom service which allows configuration of multiple parameters (perhaps 50 or more - which control registers in external peripherals)
I've looked...
I am reading the device manager code of SDK10.0.0 for nrf51822. I came across the dm_gatts_context_t , dm_gatt_client_context_t . I didn't understand what they store in their...
test1.hex
1.png
2.png
When i used board 0 extension board to program nRF24LE1 QFN24 OTP/Flash. it notification of error "An error occured when programming the infopage...
I'm looking for information about bandwidth utilization in crowded environments, something like a sports stadium.
Has anyone at Nordic collected data on potential congestion...
I write some function, it can run ok before I start he BLE function.
When I start the BLE function, the function can not run ok.
but , I get some data from APP throuth BLE...
Hi,
I've written code to use the "gpiote in event" to sense an interrupt from a peripheral (acceleromenter), but as soon as I enable the in event, I notice the current...
