Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi all!
I want to check work of AES encryption.
Some code on 51822:
uint8_t aesKey[]= {0x31,0x32,0x33,0x34,0x35,0x36,0x37,0x38,0x39,0x30,0x31,0x32,0x33,0x34,0x35,0x36...
Hi All,
I have a problem with the function sd_ble_gatts_hvx().
I have no return value when i call this function and i don't understand why ?
I have a function where...
I am running SES 3.10f on Linux. I have followed the Tutorials regarding Monitor Mode Debugging. I don't ever get the pop up box regarding the Monitor Mode debugging license...
Hi All,
My question is about available sleep modes in nRF51822.
As I can find in nRF51 Series Reference Manual, and Product Specification documents, nRF51822 chip has...
Description:
I am developing iOS app which will connect BLE and keep the connection till user don't want to disconnect. i.e we want to autoconnect BLE when BLE is in range...
Using Master Control Panel (MCP) with nRF51 Dongle PCA10000 v1.0
Segger is offering a J-Link firmware update - v6.10l:
Is this compatible with MCP? Is it safe to...
I am using RedBearLab Blend v1.0. I ran the HID_template and HID_keyboard_template. I can see the device in Win10 advertised as joystick and keyboard. Then I tried to modified...
Hello , i am going to use nrf51822 development kit ,but i am totally new for using it, i want to know that if i have development board and i want to see result but i dnt have...
Hello,
I need a little help regarding IoT-SDK 0.8.0 on nRF51.
In the MQTT-Example connection to the broker is established only when I press the button (callback), but...
Hi all,
I am facing issues when initializing and enabling the Softdevice after using the nrf_nvmc driver to erase and write flash pages. The project shall have the ability...
I am working with a MacBook Pro (El capitan) and the nRF51822 beacon and I need to measure the RSSI. I understand that the app nRF connect can do it, but the antenna on my...
Scenario is as follows:
NRF52 (SDK12.1, SD3.0) works in central and peripheral mode.
What happens is that on start we create a single shot timer with 4.2second to wait...
I write a function, It can read ok without BLE starting.
When I start the BLE , the function can not run.
So I think that , if I can use some function to stop the stop the...
Hi, all.
I tested ble_app_uart in example directory by PCA10040 board.
It works well.
printf ("UART Start!") in main.c works well. "UART Start" string cames out on putty...
Hello everybody,
I have a problem when I try initialize the ANCS service. The method ble_ancs_c_init(); from ble_ancs_c.h return the error NRF_ERROR_NO_MEM.
My configuration...
