hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
My application is based on the ble_app_uart demo. I want to get the BLE approval from the lab. The lab want me to tell them the Bluetooth profile of my application. How can...
Hello,
I am trying to interface the STPC16CPC26 with the NRF52832. As per the datasheet of the display driver, we have to toggle two IO pins from the NRF which shall be connected...
I want to write protocol stack and my program to 518222 and now need the manually download device or the automatic download device. can you offer me the communication ways...
Hello
i am using Nrf52dk. i have Visualgdb.
i would like to use the Nrf5 IoT sdk in visualGdb.
i have some question. is that Nrf5 IoT sdk will support the SysGcc toolchain...
good time dear Engineers!
faced with a problem of S132 nRF52. ADV data of packet lost.
I compared the RAW data according to screens below:
If I use nRF Connect ...
Hi, Nordic
I see this question: devzone.nordicsemi.com/.../ , I follow it, then I can see log in J-link RTT viewer.
But when it work, I find after some time, the old log...
Hi would like to evaluate the consumption of my pcb in connected mode using a nRF51. For that I use the nordic excel tool : "APM_nRF51822_S110_v3 0c.xlsx".
But I really don...
Hi,
I am trying to save some data in flash by using the Flash data storage.
However, everytime I try to write data to the flash, the module returns this error code:
FDS_ERR_UNALIGNED_ADDR...
Hello,
I'm making bootloader(nrf51822xxAA SDK12.1.0 and SD130 version).
I have some problem in micro-ecc installation.
To install micro-ecc, complete the following...
Hi, I have a problem with DFU OTA.
I use nRF Toolbox's DFU to upload nrf51822 QFAC, most times it works.
However several times, after the app altered "** bytes transferred...
Hi,
I want to generate a 2.048MHz clock on one of the IOs of nRF52832. Could you comment on following questions?
1- Can I generate this frequency (with no load on CPU...
Hello, I work with some ADC 24-bit (HX711) and for getting data from that I need after low level on first gpio pin to fed 26 pulses to that with time period about 1us on second...
Hi,
I am using ble_app_uart_c_S120
How can i support more then 1 bonded connection?
i try:
#define DEVICE_MANAGER_MAX_CONNECTIONS 7
#define DEVICE_MANAGER_MAX_BONDS...
What's the correct settings for nRF51822 CEAAE0 (0x0079) with dfu example in SDK v11 ?
I believe the chip I am using is a 16KB ram 256KB rom version, but not sure 51422 or...
