Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I have a strange behavior with the Timers. For my project I use a Raytac module with a nRF52 Chip on it. Softdevice is not flashed. Project is based on SDK 11.0
When I...
My setup:
NRF52DK;
Keil 5.22.0.0;
nRF5_SDK_12.2.0;
S132 3.1.0
While trying to use ble_peripheral\ble_app_template\pca10040\s132\arm5_no_packs I decided to modify...
I'm sorry. I closed this question and can't reopen. I need more answer.
If I solve all problem I'll close this question.
As you mentioned I'll try HW version modification...
I've just noticed that it's possible to call ble_advertising_init() and ble_advertising_start() with params that are quite conflicting.
ble_adv_modes_config_t advertising_modes_config...
Hi dear Engineers!
We want to add Eddystone compatibility to the device.
Is it possible use nRF52 silicon radio ?
How I understand, it is not compatible with any SDxxx...
After a few minutes of running, the Power Profiling kit will start printing out "Range not detected" messages in the console. It appears to be related with the "Average" window...
Hi,
I am using mca8652fc and used device address as #define ACCELEROMETER_ADDR 0x1D
but it is not reading WHO_AM_I register properly.
I used #define ACCELEROMETER_ADDR...
I did try SPI interface between nRF52-DK and MAXIM11300.
Unfortunately, I did not successfully it work.
I used SDK_11.0.0 on nRF52-DK 0.9(Engineering B) and that
...
Hello, according to devzone.nordicsemi.com/.../ it was an example in nrf51 sdk 6.1.0. I checked it and found no files or folders related, not in sdk 6.0.0 or sdk 7.0.0 Could...
Hi,
I need to send my packets with an interval smaller than 100ms in unconnectable mode. I know, that this is a restriction from Bluetooth standard. For my application...
Hello,
I've a problem with handling interruption on nrf51dk (SDK12.1.0).
I set GPIOTE to handle interruption based on the example code "pin_change_int".
I work with the...
I am trying to use the NRF51 soft device with the App_PWM library. I can get both working individually, but when I try to enable both, I can no longer connect to the device...