Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
I'm trying out different SDK's and some of them are working to an extent (they load the softdevice, and the app, but when I test run in debug they start at a different location...
I am working with the nRF52832 pca10040 devkit, and when I program the softdevice with the nRFgo studio, the only version that shows the firmware after programming is S132_nRF52_2...
Hi,
we are using nRF51822-QFAA in our project which is based on the PCA10000-nRF51822 Development Dongle 2.0 - layout of radio part is almost the same. I'm also using sdk...
I need to read variable length blocks from an I2C slave using a TXRX transfer. The length of the following data is given in the first read data byte, similar to SMbus Is there...
I installed Bluetooth Developer Studio , (BDS), which appears to offer a way of setting up a custom profile without have to spend too much time on writing low level code....
Dear Everyone.
Hi, I develop nrf51822 with DK PCA10028. I have been optimizing the power consumption to some extent. But now I am very confused.
I use S110 softdevice...
Hello Everyone
We have a project using the Feather 32u4 BLE chip to communicate with an IONIC Application on Android.
And the huge problem is that i'm really really...
Hi,
I am interfacing HX711- 24 bit ADC for Weigh Scale to calculate weight which has
DOUT and PD_SCLK for Digital Output and Digital Input. I have the working Arduino code...
With Eddystone example in SDK12.0.0 I am trying to configure with nRF Beacon for Eddystone application but every time I change the URL " www.nordicsemi.com/" to something...
I use SPI connection according to the table .
I want to press the button 4 on tx (P.06) to transfer "hello", to write down the answer of rx(P.08) in the file on sd card in...
Hi
I'm using nrf51 to notify some data to an andriod device. I set the connection interval of my nrf51 program to 7.5ms. And I need to send 100 packets per second (20 bytes...
Hi Admin.
How can i calculate distance using RSSI. is there any existing method available? i tried statically(like 35-40=1m 40-45=2m) but i dont know actual method to get...
Hi all,
I am trying to add the iOSDFULibrary library to an existing Objective-c project via Cocoapods (Xcode 8.2.1 - target iOS 10).
I have followed the steps reported...
Hi
I've just done a few tests with the FDS system of the SDK12.2. My observation is, that the FDS doesn't properly use all assigned flash pages to reach a maximal lifetime...
