NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
I am trying to implement the following sequence, using SD s130 :
GATTS Queued Writes: Stack handled, one or more attributes require authorization (var #1)
First thing...
I started with programming my nrf52 dev kit board with the soft device (v2.0.0-7) programmed using nRFgo, and then bootloader (from dfu_dual_bank_ble example) programmed using...
setup, I have a 3.3 V battery divided down to the bandgap range using a 56k and 10k resistors, so the voltage at the ADC input is 3.3 * (10/66) = 0.5 V，but the fact is 0.498V...
When I run try to generate code for a simple Blood Pressure profile I get a run time error. I'm using Plugin 1.2 with Studio 1.0.2095. Any ideas on how to fix it?
1:25...
I'm putting out this scenario I don't understand, yet, to see if anyone else might have experienced the same thing.
I have a demo with a central and peripheral that bond...
Best Regards,
while messing around with nRF51822 S130, timeslot API and nRF Master Control Panel, we noticed that:
Issue : if a packet is formatted correctly, but the...
Best Regards,
I am developing a firmware version for nrf51822 based on Softdevice S130 (old v8.1) and Timeslot API.
Currently, I can freely transmit and receive packets...
I'm using the NUS service for a sensor design. It was working fine for me. I don't know what is changed, but I experiences the next problem.
When I connect my sensor using...
What is the RF Connector on NRF52 Preview DK? It looks like U.FL/IPEX/MHF but it does not have the central pin. I want to find a converter to SMA. Could you please suggest...
Hello,
I am currently working on a hard metal project involving Nordic product with Bluetooth.
I have to implement Bluetooth Smart for a bare metal project and I've already...
Hi,
I have an nRF51822-based peripheral with S110 softdevice, and it would be handy if I could nose around central's capabilities when it connects my device (I'd like to...
Hi,
At the moment I try to communicate with an external EEPROM. Writing to the EEPROM seems to work. But when reading back the written data, the program breaks... :-( ...
Hi, In my project I need to program softdevice+bootloader+application at a time, for these previously I used mergehex tool to merge Softdevice, Bootloader,application and...
Hi, I use nrf51822 with SDK9.0, gcc with makefile, and soft devices S110 or S130 on Windows. I would like to learn how to load firmware using the wireless DFU app from within...
