Hello,
Is the NRF7002 pre-certified for the RADIO EQUIPMENT DIRECTIVE 2014/53/EU (RED directive) ?
Is there a recommended antenna design that would ease certify a product...
Good day, I was attempting to test the radio performance of the NRF54L15. I ported over the Radio_Test sample project to try and transmit an unmodulated carrier wave at a...
My task is to mount a littleFS system on the external flash memory, so I can save files.
I am using the littlefs filesystem sample from
zephyr/samples/subsys/fs/littlefs...
Hello.
How often are the LQI and RSSI values in the coordinator updated for a child?
Preferably I would have liked to get some kind of notification every time LQI and...
Hi,
I want to configure P1.02 and P2.06 as normal GPIO for my nrf54l15 custom board. For this I have added the following in my .overlay file
From https://devzone.nordicsemi...
Hi Nordic team,
I’ve been working with the nrf_dm sample from NCS 2.9 to perform distance measurements using multiple nRF52840 devices. The sample works well, and I've made...
Hello
I'm working on a custom electronics board with an nrf54L15 (QFAA). This MCU is interfaced with an EEPROM memory (24FC16T) via an I2C bus connected on P1.03(SCL) and...
Hello,
can I change the message that appears in the notification bar of the beacon server lib for Android 5.x? I know how to do that. I would like to know if it is allowed...
Hi folks! First post here. Can anyone recommend an external amplifier (preferably preamp and PA, but just a PA will do) for the nRF905 for use at 900MHz?
Thanks,
-Dave...
Our system will awake from an external accelerometer interrupt, so I would need a code fragment which shuts down S110 soft device (and radio of course) and also all the nRF51822...
Hi,
I'm trying to test a new nrf51 board using the s130 softdevice and the ble_app_hrs_130 example. However, the program seems to hang in the ble_stack_init function (code...
I'm trying to implement DFU-OTA (Bluetooth transport) for our custom board and currently i'm facing problems in flashing the different elements (softdevice, bootloader, application...
I need to implement a PWM analyzer. I looked at the example in SDK 6 and it's fairly easy to follow. When I tried it, it doesn't look like GPIOTE handler gets called frequently...
I'm trying to backport the code form SDK 9.0 to SDK 7.2,
but i need to make sure that can be supported.
I found the "ATT-51", and there is a table about that,but the last...
ble_dtm.c has some bugs related to signed integer representation which prevent negative power (less than 0 dBm) from being requested in the vendor specific message.
...
Hi, all.
I'm using "SEGGER_RTT_printf" for debugging. Because have no uart port on my development board.
I want print double type variable like below.
double pi...
I am currently trying to communicate with a GPS module using the UART on an nRF51422 (using the Dynastream N548M5CB module). I am using SDK v9.0.0 and the FIFO version of...
Hi,
I want to send a continuous stream of data very quickly into the nRF51 through SPI and then dispatching it to a smartphone via BLE.
However I keep getting BLE no...
Hello
When i am in keil uvision 5.18 and use the pack installer all the examples using Softdevice S110 are gone in Keil. Is this a known issue and is there any way to solve...
I followed the instructions and comments in devzone.nordicsemi.com/.../ . I built a project around the ble_app_gls example (with a couple of minor changes such as using -DNRF_LOG_USES_RTT...
Hi, I would like to program nRF51822 flash over SWD interface. I have another micro LPC1100 series that has the flash image for RF51822 and connected to nRF51822 over SWDIO...
