Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
hi,
1.I find some same issues on website, most of them can send more than 1 packet per connection interval up to 6 packets, but I'm not sure what version of sofedevice...
Hi!
We are using S130 softdevice in peripheral role and achieve the specified maximum throughput of 63.4kbps ( S130 spec ) when communicating with a PC and connection interval...
Dear sir,
Reader has a NRF24L01P-R7 with stm32f4xx controller.We are using TAG chip NRF24LU1P-F32Q32-T.
Please share the independent stack information(source code) so...
I am trying to setup the examples for the dev board PCA10040. I copy them from the Pack Installer and when I open the project I keep getting "Install missing Software Packs...
Hello
I made a custom service with characteristic. It send the number 1234 over ble. When i open the Master Control Panel and look at the custom characteristic. I read...
We have a home made BLE device based on nrfR1822. This one has two embedded sensors sampling data at a frequency of 25Hz.
In regular mode, the device sends every second...
I was going through Gazell link layer as well as Enhanced shortburst i found in both of them we can use payload max upto 32 bytes. Both supports 8 nodes with an host using...
I just received the nRF52 demo board PCA10036 V 1.0.0, and I also downloaded the latest SDK nRF52_SDK_0.9.2_dbc28c9
I programmed the softdevice hex and then programmed...
Hi BLE Developers,
I'm developing a BLE peripheral device using S110 softdevice which doesn't have any input or output capabilities and will communicate with smartphone...
Hi,
I am using the iOS nRF Toolbox and integrate it to my Swift project.
After that, I got this error message.
Undefined symbols for architecture x86_64:
"_crc32"...
my dk board : nrf51422 and nrf 52382,
the central role : nrf51422, and the peripheral role is 52382.
my sdk version : 52422 is 10.0.0 and 0.9.2 for 52382
the project...
I've been trying to wrap my head around the app_twi library by looking at the examples, and I'm slowly getting there.
However, for my application I need to send multiple...
There is a fair amount of documentation suggesting that a Raspberry Pi or consumer router running OpenWrt can be set up as an edge router for Bluetooth.
The builds involve...
