When transitioning from ncs v3.3.0 to ncs v3.4.1 noticed a warning about CONFIG_BOOT_ECDSA_CC310 being depreciated when building MCUboot. The release notes suggest using PSA...
Hi everyone! I'm having difficulties in setting up a little project in which I want to pass I2S data over USB. I know I'm using the old USB Audio Class endpoints, but everything...
Hello,
Thank you for your help.my questions are as follows
SDK : ncs 3.4.0
Hardware board ：nRF54L15
Based on the ncs SDK 3.4.0, how should one set the MAC address...
On a custom Zigbee End Device application for the Thingy:53 (NCS v2.9.3), ZCL Configure Reporting commands sent by Zigbee2MQTT are rejected with ZCL status FAILURE for almost...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
I am using is25lp03d flash with "nordic,qspi-nor" driver.
The issue is that nrf_qspi_nor.c driver uses `nrfx_qspi_mem_busy_check()` before entering suspend mode. This function...
The %XCONNSTAT read command returns the total amount of data received/transmitted "in kilobytes". By kilobytes, does the documentation mean 1000 bytes or 1024 bytes?
Hi
I would like to have a project using 52840 witth softdevice 17, and I need to use internal flash to make a USB mass storage device
I reference to ....\examples...
Hi,
I need to create partition of size 4kb but using psa_ps_set() I could not able create partition of size more than 1Kb, If I try to create 4 kb Partition it's throwing...
Hello,
Creating a simple project in nrf connect 2.6.1 I start with looking at power consumption.
I need upgrade over USB, so I have added this to .prj:
In the...
software: ncs 2.5.0, zephyr\samples\drivers\counter\alarm
hardware: nRF52840dk
Step1: main.c is not be r evised!!!
Step2: prj.conf like this:
Step3: overlay file...
Hi Nordic Team,
I am currently working on a project that involves two devices, both using the nRF52840 microcontroller.
Current Setup:
Device A : I have successfully...
hello Nordic
we are working with ncs v2.5.0 trying to migrate to 2.7.0
1. so that there is several rcs, should i take v2.7.0-rc3 or v2.7.0 ?
2. while choosing v2.7.0...
Hi all,
I wonder if nrf9160 has a built-in temperature sensor interfaced with the ADC, that could help to diagnose the internal chip temperature?
Thanks.
I would like to use the Power Profiler app (with PPK II) as a pure coulomb counter for accurate long term (> many days) cumulative device energy consumption without saving...
Hi there,
We have a product running on nRF5340 with an existing workaround that was carried over from an nRF52840-based product, where SAADC readings are prevented from...
Hi Nordic Team, I'm currently working with the nRF5340 Audio DK to broadcast multiple streams, where the receiver can select which stream to listen to. To the reciever, this...
I have an ILI9340 connected to an nRF53 and want to use LVGL in Zephyr (NCS 2.6.1), but I got no label, etc. showing up. Instead, the display is showing a white screen.
...
Hi, I would like to interface an Alliance NAND flash to NRF5340. The flash supports SPI interface. Which set of pins will be a better choice and why ?
I am planning to use...
Hey Everyone, I am new to Nordic and zephyr. I would say I am a beginner. I am trying to setup custom drivers from ST for the lsm6dsv16x sensor. I know most of the time is...
