Bluetooth physical layer Direct Test Mode testing is used to verify BLE low-level RF transceiver performance. The required software is nRF Connect for Desktop V3.7 + Direct...
Hello,
I am using WM02F WiFi mdule with nRF7002 SoC and i am having some issues with the TX power measurement of the WM02F WiFi module while operating it in 2.4GHz.
I...
Hi,
We have two option to use Flash memory,
Option 1: We are planning to use Flash Memory on the SPI bus shared with the NRF7002. Kindly confirm whether this configuration...
Hello,
We are currently performing power consumption measurements on the Nordic nRF9151 using the PPK2 in LTE-M with an Objenious SIM card.
During our tests, we observed...
Hi everyone,
we are running a Cloud-to-Cloud scenario where we use the Assisted GPS API.
https://api-docs.nrfcloud.com/#tag/Assisted-GPS/operation/GetAssistanceDataLegacy...
Hi everyone,
I have created a new sensor driver using the Zephyr Sensor API, including support for:
sample_fetch()
channel_get()
attr_set()
attr_get...
Hello,
I am working on a custom development board that is using the nRF52840. After programming the nRF52840 on the board with Soft Device s140_nrf52_7.0.1_softdevice.hex...
Hello DevZone,
A product I use uses NFC tag type 2 to communicate. It usually communicates to a separate chip but I want to replace this with the nRF52832.
I opened...
Hello,
I'm working on a product where we want the nRF52840 to be able to reset itself in hardware . This is currently done via an IO that drives a SHUTDOWN# signal into...
Hi,
I'm using TWI to control accemeter(MMA452).When I used TWI SENSOR to read my sensor, it didn't work normally.
The address of MMA8452 is 0x1C,so i want to read...
The separation of flash memory into a region for the application core and one for the network core on the nRF5340 seems rather cumbersome and error-prone.
I'm especially...
Hi,
will qmi_wwan or gobinet driver be available for nRF9160? PPPD is not available. It is quite a limitation in use to miss ethenet interface based connectivity.
Regards...
Hi everyone, I’m have a wired network of 1000 devices (relay switches) that I’ve been tasked to upgrade to wireless.
Devices are inside a warehouse, about a pallet apart...
Hello All,
I am developing product using nRF52840 Dev-kit and SDK 4.1 for zigbee and thread.
I have created the new solution using tool chain - C:\Program Files (x86)...
Hello,
I'm using the NRF52840 with the NRF5 SDK v15.3.0 and S140.
I was trying to include the nrf_fstorage library into an existing project. The problem I experienced...
Hello,
I modified a sample app "blinky" on segger, to include main.cpp instead of main.c Then when I built, I got a compile time error stating in main.cpp "void main(void...
Hello.
I'm looking at options for a BLE device that has fairly small application requirements. It would essentially be a button, so the peripheral blinky example would make...
Hi Nordic!
We are gonna do pre-compliance testing of our custom board, with mounted nRF52840 and nRF9160 SICA B0.
We are looking for any software available from Nordic...
Hi,
with reference to case ID:278209, I was suggested with a resolution to add in CMakeLists.txt I need information on all such (CMakeLists.txt) available tags/labels...
hello,
I tried to read adc sampling value from (NRF_SAADC_INPUT_AIN0~ NRF_SAADC_INPUT_AIN4) with pip mode.
Here are my code as followings
If I have no any voltage...
Hi, there.
I'm trying to implement DFU over UART for a NRF5340. I have read the documentation and have understood this will require the use of a bootloader and I wish for...
