Hi,
I am trying to configure an Xiao Seeed Studio nrf54l15 sense to transmit pre-processed sensor data via BLE extended advertisements. As the payload is more than 251 bytes...
In this post mentioned: "Maximum theoretical peak data rate is 3.4 Mbps when transmission is scheduled into packets of 4 slots using MCS4, and these 4 slot packets are transmitted...
I want to use a new source LF clock to raise the precision from +-250ppm to around +-20ppm. I already have an oscillator mounted in my PCB, so I want to use it for BLE. I...
Hi,
I would like to know if its possible to run Azure FOTA functionality w/o using Partition Manager (aka `SB_CONFIG_PARTITION_MANAGER=n`) ?
Trying to build this gets...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Hi everyone,
I’m trying to program/recover a custom board with an nRF52840 Fanstel module using a Nordic nRF52840 DK as the programmer. The board is powered from a 4.2 V...
In the absence of a QGAA reference, is there anything to be aware of when designing a QGAA board?
For example, with the nRF52840, the WLCSP and QFN references used different...
Hi,
i have nRF52840 DK.
I am working on radio test code based radio_test example code with nRF5_SDK_17.0.2_d674dde version.
If the transmitter is configured as : (BLEN...
I can't build examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay. I get the following error message:
cc1: fatal error: cannot open 'C:/.../examples...
Hello,
After looking at aws_iot sample files, I've stumbled upon the question regarding how one can dynamically change IDs and certificates for multiple 9160 devices? I...
From yesterdays question https://devzone.nordicsemi.com/f/nordic-q-a/80411/state-of-cs-ss-pin-after-nrfx_spim_xfer I have done a logic measurement and I can confirm that after...
Hi,
schematic for CFAA WLCSP mentioned, QDAA is given in the documentation. I want a reference for Circuit configuration no. 1 schematic for CFAA WLCSP mentioned in the...
Hi
I am using nrf52810 chip. we are trying multilink with central(1 central and two peripherals connected at a time),one central and one peripheral is fine, but we are trying...
Hello!
I am using nRF52-DK to deploy my programs. I try to use writing to SD card in ble_app_uart_central example. Both fatfs and ble_app_uart (central) examples work...
What are the memory settings in the SES compiler to compile secure_bootloader_ble_s140_pca10056
When I try to merge:
mergehex --merge s140_nrf52_7.2.0_softdevice.hex target_application...
I want to write some values to flash before the watchdog resets. For this I have the watchdog event handler specified:
In the wft_event_handler function I write a struct...
When trying to generate a new project Segger Project for my Project
in the option "Extra CMake Build Options" want to pass something like -DCONF_FILE='prj_test.conf' -DDTC_OVERLAY_FILE...
Hi Nordic team,
Looks like the most recent nrfjprog now supports flashing modem firmware.
I tried it and got some errors. Could you please point me in the right direction...
Dear Nordic Team Support
We face an issue where on different computers, using the same setup, different throughput can be achieved.
Setup:
- Custom Device using the...
Hello community...
I was able to compile the GPS sample and flash an actinius icarus (nRF9160) using the Actinius Programmer once and it said successful.
However, the...
Hi I need the upstream Zephyr project for direction finding functionality and bug fixes. Those are not present in nrf-zephyr fork.
How do I get that to work? Just replacing...
