Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi,
I have nRF52840 DK, and PPKI power profiler, I measured peak current mA using PPK on Radio Transmitter, And I found there is a big discrepancy between measure and typical...
Hi Guys,
We are currently working on a mesh sensor network. I have already developed a vendor sensor model (client and server). The client will also work as a gateway and...
I have a couple of questions regarding the nRF52840 internal voltage regulators, specifically REG0. I couldn't find the answers from the datasheet and therefore I hope that...
I started using nRF Connect for VSCode a couple of days ago on one computer and it has been working great. Now I had to switch to a new computer where I had also just briefly...
The first chip silkscreen for 2050ST second chip silkscreen is 2109XN third silkscreen is 2052TJ, transmit power configuration for 8dBm actual test from the chip side, test...
Hi, i'm using STLink V2 for compiling the code, the weaknes of this compiler is you can't see the result debuging or serial print output.
so i'm using USB TTL to see output...
Hi all
I am using nrf52840 kit, and I have a simple BLE app(client/central that turn LED on to a connected server/peripheral) running on it(sdk 15.3). Now I want to put...
Hi,
I'm using nrf gateway application in android and it is not able to connect to nrf cloud. I have reinstalled it but still the it say 'Gateway connecting...'. Please...
To the kind attention of Nordic support team,
Is there any update about this topic:
https://devzone.nordicsemi.com/f/nordic-q-a/59738/usb-device-suspend-resume-issue...
Hello, I managed to run nRF5340’s QDEC on development kit. The dts overlay looks like this
The problem is I do not see the LED gpio (P1.13) switching on and off on the...
The datasheet appears to say that a pin_reset does not completely reset the chip:
in particular it does not reset the SWJ-DP interface which, I believe, in some circumstances...
HI,
I'm developing it using NRF52832.
It is intended to update the remaining battery capacity through the battery_level_update() function by receiving the battery measurement...
Hi,
Few Binding APIs are absent in nCS as compared to nRF5 Mesh SDK. Compiling some models for certain boards is generating compile time errors, is it that certain models...
Hello! I am currently looking at options for unit testing frameworks ( for TDD and CI/CD) on host OS(Windows preferably but Linux if I must) for nRF8233 core custom boards...
Hi,
We need to save 3 strings to flash using NVS. Based on the code sample in zephyr\samples\subsys\nvs we set the initialization and then write and read these data.
To...
