Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
Current I am using nRF52840 Dongle to develop a Bluetooth PC Tool base on nrf_ble_driver_obj_sd_api_v5 which shared on https://github.com/NordicSemiconductor/pc-ble-driver...
Hi Nordic Dev Team,
I need suggestion on how to achieve this. My microSD saves chunks of 50kB raw data.
I would like to retrieve this data once connected to the phone...
Hello,
I am trying to receive advertised data by a sensor which is easily detected at nrf connect app and whenever data changes i am able to see the change in data on nrf...
I am trying to send a lot of data and I am trying to do this with notification. As I understood notification do not need acknowledgment and should not use que for messages...
Hello,
I am using SEGGER embedded studio to develope a project. I want to know how can I know the flash and SRAM use of part code. Because I have many files. After I build...
I am using the nrf9160 for an OTA firmware update application. After going through a lot of tickets and some documentation regarding the nrf, I have not been able to find...
I want to use the register of Nordic's P0 port directly to set 1 or clear 0. Like this,
p_reg-> OUTCLR = clr_mask;
P_reg - & gt; OUTSET = set_mask;
p_reg-> OUTCLR...
Currently we are developing against hardware sensors etc. that we have installed in our warehouse
It would be great to be able to develop remotely (ie. from home) without...
Hello Nordic Support Team,
I'm using nrf52840 DK for DFU update over ble with nrf5 sdk previously it was working fine and i was using nrfutil tool to generate settings,...
Hi,
I have downloaded the nRF5 sdk v17.1 and used the peripheral blinky example with pca10056e and S112 soft device and modified the preprocessor defines and this example...
Hello Everyone,
I am working on NRF52840 and we had enabled the APPROTECT feature in our firmware. The code for implementing this is as follows:-
void init_mem(void) ...
Hello,
I know that the bt_ctlr_set_public_addr() interface needs to be called before enabling Bluetooth, and this bt_id_create() .
But I read the description of bt_id_create...
Hi,
The nPM1100 Specification states in section 7.2 that:
An application should not be supplied directly from VBAT because it can disturb the battery charging process...
Hi everyone,
I wish know how i can set BLE_GAP_TX_POWER_ROLE_ADV at peripheral and BLE_GAP_TX_POWER_ROLE_CONN at central on UART example provided on nRF Connect SDK v1.6...
