Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi,
First off, I'm very new to the nRF52 development so I'm suspecting to have done something wrong...
The datasheet of the nRF52 832 states a current consumption of 0...
Hi,
I have been tryring to identify the characteristic who is requesting a read. To do so, I implemented the read authorization request. Here is my code:
Basically...
Hello,
I'm trying to receive an inverted UART signal on the Arduino Nano 33 BLE (NRF52840). I've been able to invert the transmit signal okay using two GPIOTE channels and...
in ble send data period ,nrf 5340 CPU seem to be shared only by ble send
data ready and data read in ble not send period can equal ,this mean every data come from ecg chip...
Excuse me:
I'm testing the maximum rate of ble_app_uart。
1、Can the nrf connect app on IOS initiate the update of MTU and PHY?How to update MTU and PHY on IOS nrf connect...
I use nordic5340 SPI read ADS1298R ecg data, using nrf5340 p0.13 to connect ADS1298R data ready pin . when ADS1298R data ready pin high to low mean ADS1298R data ready .i...
Hi guys I am new to Nordic, just made a DevZone as the technology isvery interesting to me. So far I have been playing with ESP series but I know nordic is in a class of its...
Hello everyone,
I have been working for a few days with nRF52833DK building a BLE mesh where one of these microcontrollers is a client node or a server node.
However,...
Hi,
I have several questions about the dongle board.
1. Why should the p0.19,20,..,25 be connected to the reset pin?
2. what is the difference between the reset button...
Hi, All,
I saw the options for S2 and S8 in conn.h of ncs, but i don't know how to use it.
And I want to test the relevant data and differences between S=2 and S=8 broadcasting...
Hi Team
In nRF5340 Product Specification v1.1 page 117. The CACHEDATA is mapping as secure. But it have trust zone ID 252. So I have below questions
Does cache only...
This is a strange problem. 10% of our production boards fail outdoors within tens of seconds and will not fail after tens of minutes if indoors . The rest of our production...
Hello,
is there some existing example for nRF52840 DK, that would allow setting my own custom HID descriptor? e.g. "Telephony page (0x0B)" or a custom vendor-specific HID...
