Hello,
I have downloaded the newest Zigbee R23 SDK (v1.3.0).
When I use the feature inside VS Code: "nRF Connect" -> "Create a new board" to create my custom board...
Hi
Currently I'm evaluating the nRF54L15 die temperature sensor. I’ve taken a few measurements and noticed something I don’t quite understand yet. Perhaps someone could...
Hi
We used ALA321C3 like antenna for the chip nRF54L15 , but we have a little probleme that the signal of it is not stable.
So we need your teams to help us.
And we...
I have around 140 BLE Scans per second in my environment. I can see them with a NRF52840 with SDK 17 and with an ESP32 as well.
But when I scan using NCS 3.2.2 I only get...
I am using the nRF5340 development board to program the LBS example from the NCS SDK2.7. After system-off, the current is still several tens of microamps, which differs from...
So I have two questions. My first is on the impedance matching network on different pcb stackups. So wouldn't I need a different matching network for a different pcb stackup...
Dear Support,
I'm using nCS v3.1.1 and the Matter example project. Could you please provide a simple example showing how to use GPIOTE + DPPI + TIMER capture?
My goal...
Anyone able to run the nRF9160 DK on Window 7? I see the 3 serial ports and the mass storage device but even though I see the device in the Programmer app I get "Unsupported...
Hi dear,
Good Day!!
I am using nRF5SDK1702d674dde\examples\ble_peripheral\ble_app_uart- software to test the UART over the BLE to my mobile , The BLE was automatically...
Hello,
i am using "ble_app_uart" example code in nrf SDK to connect to bluetooth and to read-write the data after connection through nrf connect application.
write...
We are using a custom board with softdevice S132, sdk14, and freertos and ana nrf52832.
Our ble_app does:
init gpio put up a splash screen via a display on spi
...
I am starting a new project using SDK 17.0.2, DK52 dev board and Segger embedded Studio.
To create the new project I started from ble_app_buttonless_dfu and commented out...
I got the update notice for 3.6.1, the install gets to around 33% then just sits there. This happens both with upgrade and with clean install for me, I left it to hang for...
Hi all,
in my current platform I have:
a DK (we are working to implement HW modifications to use a nrf52 dongle for this purpose) that is performing as a Thread DFU...
Hello,
I am currently trying out the assert mechanism of Zephyr.
I have added CONFIG_ASSERT=y to my prj.conf file and included " sys/__assert.h " in my main.c .
My program...
Hi,
May I ask what's the minimum reference circuitry for running nrf52840 without RF? Thanks.
My scenario is as follows.
1) RF, eg, Antenna is not needed
2) GPIOTE...
Hi,
I'm developing a CENTRAL using 52832 to connect a earphone.
1.When I enable LESC, the pair fails with the AUTH_NOT_SUPP error. Why ?
What I think if the earphone...
Hi.
I'm trying to use direct advertising to connect only with devices that have already been paired.
When I start direct advertising, I get a app_error_fault_handler...
Hello,
I am using nrf52832 and I just have 3 questions regarding it.
1) SAADC change over temperature. According to the datasheet, it has a change of 0.02%/C but I only...
Short version: can I use a pin both as a GPIO input to trigger GPIOTE PPI event, and as SPI MISO *at the same time*?
Detailed version:
I want to use the SPI peripheral...
