Hi
I'm using NRF54L15 DK from Nordic. I have installed VS Code and NRF Connect SDK and toolchain V3.4.1.
I'm following the Fundamentals course, and doing Lesson 1, exercise...
Hello,
We are seeing a west build reproducibility issue on nRF Connect SDK v3.4.0 that we have narrowed down, through extensive elimination, to the compiler's code generation...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151-LACAA1A design, and I would like to make sure I understand the recommended correction for...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151 design, and I have three related questions about BUCK1 and the 1.8 V rail.
1. nRF5340...
I have been testing the HTTP FOTA procedure as documented here using the 1.5.0 test diffs as provided in .
Many of the messages output by the modem in this upgrade process...
While trying to run the FOTA-TEST upgrades from I came across unexpected behavior when the same script fails twice in a row. I first attempt to trigger a FOTA with the following...
Quoted from Heidi’s blog post Target Wake Time on the nRF7002 DK , published 23 Feb 2023 (available at https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/target...
HI:
I Use the Projtcet: "......\nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_uart_c".
In the BLE_Central project, how to set the Tx Power??
thank you very much...
Hi , when i first recived my nRF5340 DK it had an preinstalled code that maked the leds to fade depending on what button i pressed, but now when i try the example codes on...
Hi,
We're running the aws_iot example and it would seem that by default it does not use the certificates in the file certificates.h
Is that the case and how can we use...
Hi,
I'm new to the whole Nordic environment, and I need to develop an application working with ble and lteM, so I have an nrf9160 DK for this purpose.
I worked with the...
I have a custom board based on NRF52811. Salient features:-
Both HF and LF crystals are present on board.
Power supply is 3.3V.
MCU DC-DC is enabled.
I am using...
Hello.
I trying the test for real time transfer a data.
Period is 4 ms and 5000 point data. (Total 20 sec)
The GPIOTE event occurs every 4ms and the processed...
how to unpair our nrf52 device once it's paired with another nrf52 device, currently we need to switch off the device so that we can pair another device.
Hi all,
I have a customer that has requested NRC tap to pair functionality for their device, mostly for convenience. This is fine, but I'd like to know what they're getting...
Hi,
We are running into a weird issue with some our devices when they are in the bootloader.
The bootloader fails with this error in nrf_dfu_validation.c: Invalid protocol...
Hello,
We have a firmware with 2 versions that runs on Baremetal and FreeRTOS on nRF52840 DK. We would like to port this firmware to nRF9160 without Zephyr and continue...
Dears.
when I connect nRF52833 to connect DK board, JLINK is ok .but could not find device from target device selection.
nRFGo studio is the same. what's the reason for...
Hi All,
I am able to perform the OTA DFU from the NRF52840 Dongle using the NRF Connect Bluetooth low energy application and default Nordic firmware.
I would like to...
I have a service with 2 characteristics, TX and RX. On TX the notify is enabled, because TX should send a notification when something changes. I manage to change what is needed...
Hello everyone.
We have a design based on NRF52840, which uses the built in USB peripheral and was fully tested and prototyped using NRF52840-QIAAD0-2031MR. We have now...
