Hi Nordic team,
We are planning to use the STM32H747 as the host MCU to control the nRF7002 for Wi-Fi functionality. Based on reference materials and existing use cases...
Hello Nordic team,
I am working with the nRF54H20 and would like to integrate both Enhanced ShockBurst (ESB PTX) and Bluetooth Low Energy (BLE peripheral) protocols in my...
Hello, I'm testing the nRF21540 FEM on a custom nRF52840-based board using the nRF Connect SDK.
I’ve enabled CONFIG_MPSL_FEM CONFIG_MPSL_FEM_NRF21540_GPIO_SPI CONFIG_BT_LL_SOFTDEVICE...
Hello, checking if I'm doing this right of restoring initial fw for 91X to work with Quick Start v1.2.0. as described here in Get Started, https://www.nordicsemi.com/Products...
It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
Background
For reasons that I do not want to dispute here, I am building a custom bootloader for the APP + NET cores on the nRF5340. This custom bootloader is not a Zephyr...
I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
Hi,
Does nRF5340 (or any other nRF52XX) support natively ISO7816-3 (SmartCard)?
"Natively" means using USART or any other way(hardware of official software) other than...
I am reading the PPI Example at the Infocenter as shown by the link below: -
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v11.0.0%2Fppi_example...
Hello Nordic,
I worked with the interactive PyACI during several months by using my PC (running the interactive PyACI) connected through usb to a DK used as provisioner...
Hello,
We've recently migrated from SDK version 15.2.0 to 17.0.0 and noticed an anomaly with the clock driver. If the watchdog is started, then after any soft reset (through...
Hello! How can I measure the heap size (total and free space) at runtime?
Right now I'm working with some legacy code that makes a call to mallinfo()
That call returns...
I am testing "nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\experimental\ble_app_cli" example.
Do I need 2 boards to run this example ???
What I got from the infocenter...
Hi
I am using SDK17. I am running the app_pwm example and i get an error with the "nrf_drv_state_t", it is not defined and the "NRF_DRV_STATE_POWERED_ON" is not defined...
Hello,
I'm programming nrf52 with SDK17. My application requires to advertise in 1 channel and also scan in 1 channel too. I have done the code. But when I run the code...
Hi,
I'm programming nRF52833 for my application. I have done to configure my device and it advertised and scanned sequentially. For my application, I advertise and also...
Hi:
I am trying the "Mesh Serial" example on my nrf52840 boards. However, when the Echo command is used after the device is cold-started , a timeout event will occur. I...
hai ,
i am using nrf52840 sdk 15.2 and in my application i have to connect nrf52840 central to peripheral after connection i have write data on ble_lbs_led_status_send i...
Hi,
I am using NR52832 with nRF5_SDK_15.3.0_59ac345 .
I want to scan nearby mobile BLE devices and get its data from its advertising data and also its scan response data...
Hi,
Hi, we have a latency-critical use-case and found the Low Latency Packet Mode ( LLPM ) as a possible solution.
Our current application is using nRF5 SDK 16.0 with...
Hello Devzone
Currently I am following below link to setup the “HID configurator for nRF Desktop”.
link: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf...