Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi
sir we have nrf9160-dk and planning to interface some sensors to it but the issue we are facing is that the gpios are at 1.8v where as we need 3.3v logics to interface...
Hello everyone,
I getting stocked now for 1,5 days to get the nRF-Connected SDK running
I am using macOSCatalina 10.15.7
segger 5.20
Nordic SDK Tag v1.4.0
using...
Hi Team,
I'm working on scanner and NCS/Zephyr bt_le_scan_start callback API
typedef void bt_le_scan_cb_t(const bt_addr_le_t *addr, int8_t rssi, uint8_t adv_type, struct...
Hi
I have implemented a custom DFU process, where NRF52840 sends another NRF52833 an image to program.
The NRF52833 receives the image and validates CRC, if all OK , I...
Hi,
I'm using a nrf52833 in may application.
I have 2 Identical units with bare nrf52833.
refer the unit as normal ad defective.
test a.
while flash a simple FW...
Hello ,
I am using NRF 52 DK 15.3.0 SDK and ble_free_rtos_hrs example , I want to have a feature to start and stop the advertisement ( by interrupt driven , task notify...
Hi Nordic..
currently we are going to implement serial bootloader dfu from other MCU (infineon chip).
We have create flasher from MCU to nrf52832 to do serial fw update...
Hi
I am using nrf52832 .i am trying to connect to a device using sd_ble_gap_connect but i am getting NRF_ERROR_INVALID_ADDR error.
i am modifying ble_app_cli to achieve...
Hello
I'm going to use J-link's virtual port to see the characters being printed.
I connected custom pcb to Vcc, Swdio, Swclk, Gnd pin and tx, rx pin of J-link.
And...
In our mesh application, we are trying to give all our devices the same network key. As we are planning to have in excess of 100,000 devices, the 2-byte unicast address is...
Hello,
I am developing thread network and i am building on top of mqttsn_sleepy_publisher example. But I have problem to enable RTT logging (UART not available) for thread...
Hi, We are using nRF52840 in our design. the pin p0.10 is marked as LOW-FREQUENCY I/O (up to 10Khz) according to your recommended usage. Our software is design to generate...
