I have recently purchased nRF52840 dongle which I wanted to use as a ZigBee sniffer. I bought it on AliExpress and it supposed to be original Nordic board, but it turned out...
Hi,
I have a project requirement to interface with HART, which is a protocol that specifies odd parity for UART. I recently found out UART odd parity isn't supported on...
Hi Nordic team,
I am working on nRF5340 and trying to enable MCUboot serial recovery DFU in single-slot mode with both signing and encrypted images.
Environment: 1. SoC...
Hello Nordic Support Team,
I am experiencing a startup issue with the nPM1300 PMIC. Below is the summary of my hardware configuration and the behavior I am observing:
...
Hi Team,
I am working on an nRF52811-based BLE application using nRF Connect SDK (Zephyr) and facing an issue while trying to store the device name in flash using the Settings...
Hello Nordic Support,
We are developing a project using two setsof nRF5340 DK with the nRF7002 EK attached. We are trying to achieve coexistence between Wi-Fi in SoftAP...
I try to get the one button sample to work. There were several details missing to be able to compile and run this sample, which was very frustrating. After editing/updating...
Hi,
I included pwm code in my code and its related libraries and drivers.I am getting errors like these :
I removed non-Softdevice paths from the user include directory...
I'm trying to use this API: NRF_STATIC_INLINE void nrf_rtc_subscribe_set(NRF_RTC_Type * p_reg, nrf_rtc_task_t task, uint8_t channel) to set DPPI subscribe configuration for...
Hello, I'm Jongryul
I want to deliver voice through BLE.
I wonder if this chip supports voice command.
If this chip does not support voice command, I wonder about the...
I'm trying to create a siren tone using the pwm library, that ramps up and down between 2kHz and 3kHz.
Initially I started with the example provided in SDK v15.3.0 nRF5_SDK...
hello community!
Recently I got urgent job to rewrite sensor firmware to nrf52832.
Its not my project basically, another company project.
I wonder why rf52832 didn...
I understand with LTE-M they are supposed to offer greater distances to the cell site, but how do we tell how far away we are from the cell? In the good ol' days, we could...
It says under the S113 information that is supports extended advertising yet I can't see it in the API. I would like to take advantage of the 255 byte advertisement size for...
I want to use NRF9160 for development, now I want to pick something bootloader, so which one do I use
1. \ zephyr, replication, bootloader, McUboot \ zephyr
2. \ zephyr...
I am trying to develop a product with your nRF905. I have two units set up, and can read and write via SPI. However my concern is your poor documentation.
You do not say...
Hello, this is the person who asked about " devzone.nordicsemi.com/.../question-serial-output-uart ". First of all, thank you very much for your sincere reply.
The reason...
Hello
I would like to view the changes in sensor values in real time in a graph. Can you recommend a tool from Nordic or an easy-to-use program?
Thank you.
Sometimes during a DFU update, the NRF52811 can stay in bootloader mode (seen with name DFUTarg and mac_address equal to mac_address +1). I am on Softdevice 16.0 I'm using...
How to read values from 5 Analog pins at the same time
I know how to read from one Analog Pin, but i don't know how to access 5 analog pins at the same time and display...
Hello I am developing a prototype with the Thingy 91 that allows to have the default log in the UART0 <-> USB and collect the data of a sensor through the P6 expansion port...
I have a custom board using NRF52832 which communicates with a BMI160 accelerometer/gyroscope chip by SPI.
I have been developing in Segger Embedded Studio (v5.10d) in debug...
