Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hello,
I'd like to understand a bit more about transmit buffers for sd_ble_gatts_hvx() calls. Our peripheral application is developed using SDK 15.3.0 and S112 for nRF52832...
Hi,
reading through the gnss socket configuration parameters it came a question to my mind regarding the Power Save Modes.
Is the PSM configuration applied when the GPS...
Followed the example https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/spi
but getting spi received value 0xff each time
my conf file:...
Hello, I am a bit confused with the ARM Cryptocell 310 engine. As I can see this software is proprietary but in nrf5 sdk there is the cryptocell engine as external library...
Hi,
I am using nrf52810 ,softdevice 132.
I am trying to implement whitelist in ble_app_uart code (peripheral side).I take reference from HID mouse example.
Code compiled...
Hello everyone,
We're looking to develop a prototype of a very simple panic button. The device should automatically pair with iOS / Android, and establish a call to a given...
I have an example application executing on the nRF52840-DK on SDK15.0.0, see https://devzone.nordicsemi.com/f/nordic-q-a/67351/are-there-any-differences-between-sdk15-and...
When we try and stream BLE data to the nRF Connect app on an Android or IOS phone the app accepts our requested for an MTU of 244 or 160 respectively, however it does not...
Hi,
Dev setup:
Segger embedded studio - fatfs example - SD card - nrf52832
I am able to write to sd card and see data. But while reading i am failing.
Below is code...
Hi,
I am a bit confused after looking through all the SDK solutions available for NRF52 and need a piece of advice...
I am have started on the project that consists...
Can I periodically or continuously read the characteristic of peripheral after the connection?
If there is a change in the value in peripheral, then the value is received...
Hi,
i am trying to do buttonless dfu . I want to merge all hex files into one as per the document .when i enter the mergehex , i am getting mergehex command not found why...
Hi,
I'm making an new board with both nrF52840 and nRF9160. In addition to the radio ICs there will be some antenna diversity switches, chip antennas etc.
So I'd like...
Hi,
I'm using SDK 15.2 with Nrf52832,
I've implemented a custom service with read, write and notification services.
I would appreciate if you could send me an example...
