I'm moving to 2.9.1 and trying to get mipi working with a st7789 display. I have it working with 2.6.1 without mipi, but can't seem to get it working with mipi on a nrf5340dk...
Hello!
I want to develop a Heartrate Monitor Device which uses BLE and ANT+ using the Seeed XIAO nRF52840 Plus Board.
Now that I have the board I found out that ANT doesn...
Hi
I have one nordic nRF54L15 DK using as peripheral, I want to know the power of it. Thus, I use PPK2 to be a 1.8 voltage source and connect VOUT to P6 pin 1 and GND to...
How do I produce a signed file to flash to the network core for firmware update? I am using a child image/parent concept with the \nrf\samples\ipc\ipc_service\ project, When...
Hi,
I’m working with the Wi-Fi station example on the nRF54H20 using SDK v3.0.0, and I’m encountering a critical issue when trying to bring up the nRF7002EK Wi-Fi module...
Hi Nordic team,
I'm trying to configure the GPIOs to operate at 3.3V using the nRF Connect for Desktop's Board Configurator tool (v0.3.10). The tool works as expected...
Hi Nordic Team:
Can you help me to support BIS or CIS example .btt file。This file was captured by Ellisys tool。So ,I can refer to file ，and understand 5.2 Core Spec about...
Referencing the recommended 52840 PCB layout for the WLCSP package, we noticed two thru-hole vias in the middle of the ground area (in the center of the package). Do these...
Hello,
I am trying to implement ble DFU on our custom nRF52832 board. Up until now we have had no issues with our application running as SoftDevice+Application but some...
I'm attempting to send a time sync message in a mesh packet. When I construct the packet during it's timeslot (for timing determinism) the system faults during encryption...
We are developing using SDK 15.3.0 and S140. After I noticed that advertising stopped when a connection occurred, I was directed to simply restart upon connection. I have...
Hi,
I'm using an nRF52832 with SDK 14.2 and FreeRTOS. I'm hitting a configASSERT when I call nrf_fstorage_erase. I called the function after calling ble_stack_init but before...
Hi,
I'm using interactive PyACI on Windows i found an error as in image attached. I didn't understand what can i do with Interactive PyACI and what it will deliver to me...
Hi,
SDK 16 using board NRF58240dk. PCA 10056. Segger studio on windows.
I am trying to read a current pulse train from a peripheral device. This device outputs a 4mA pulse...
I am working with the Nordic NRF52840. I need a way of reading current pulse counts over a two wire system coming in from an external sensor. This external sensor is reliable...
Hi,
I am using 2 development kits 52840-DK.
I run the examples projects transmitter ( pca1056 ) and receiver. It works,
In an attempt to get longer range I increased...
Hi Nordic,
I had built a BLE custom service which has two characteristics and now I'm merging this with light-switch example, but while building it i got a problem which...
Dear All,
I'm pretty sure this has been asked many times but I don't know the right keywords to search for.
Alright, on our custom board we have a PMIC with regulated...
I try to start working with the nRF9160-DK. I gone trough all steps of the Getting Started Assistent from nRF Connect SDK. But i have a Problem with setting up a Project in...
Hi,
In my NRF52840 based application, I have a situation where the peripheral needs to pass 2K to central.
In order to speed up the xfer, I'm requesting a Connection Parameter...
Hi,
I am using nrf52832 and I want to build a device that can advertise iBeacon signals and can transmit data to another BLE device (central) simultaneously.
Can I do...
