Hi,
I'm using the nRF52832 with SDK version 17.0.1.
I've noticed that when the device wakes up from NFC and remains in proximity to the NFC field, it sometimes experiences...
Greetings! I've applied all the optimizations in the books but I cannot get our application to be ~50% of the available flash memory on the NRF52832, currently it is precisely...
Hello,
I'm working on a project that involves using an NRF52832. Basically, I want to collect data, send it over bluetooth, and then have the device enter system_off mode...
Hi,
Since the Toolchain Manager function to tell me about a new nRF Connect SDK has been deprecated, how do I know when there is a new/change to the toolchain or SDK that...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
I've faced an issue while performing Exercise 2 from the Lesson 2 of the nRf Intermediate Academy Course.
When I have my dump.bin created and the debug server running, after...
I'm using SDK version 15.0.0_a53641a on nRF52840 with softdevice s140_nrf52_6.1.0_softdevice.hex.
sd_ble_gap_adv_set_configure() is returning error code 7 when I use BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
OVERRUN error occurs when receiving UART.
I'm using EasyDMA with UART and want to increase the EasyDMA reception size. Which settings can be used to increase the reception...
Hi,
I have NRF52833 DK and using nRF5 16 SDK on KEIL IDE.
I am trying to compile blinky example from the peripheral and it is giving me this error
Error #541: 'NordicSemiconductor...
During production we need to provision each device with some custom data that must last the life time of the device, ideally using nrfjprog. What is the best way to do this...
There are several use cases where we want a bonded peripheral to indicate the service changed characteristic to the central.
The main case is when developping and adding...
hello can someone help me solve this issue. i am not being able to controll this led . if i send any number the led will always turn on
Regards
static void led_col_write_handler...
Hello,
I want to test the range of Adafruit nRF52840 express feather(BLE 5.0) board. I did the setup on arduino IDE. My question is can I perform the long range test of...
Hi, we have a project that we're currently working on, and we're looking for some information on BLE behaviour that would be very helpful. We are currently using SDK 15.3...
I'm trying to build aws-fota program following this instruction, but get an error https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/nrf9160/aws_fota...
I have a nRF52840 dongle.
My understanding is that the nRF52840 has an on-chip regulator (Vdd out) that can be set from 1.8 to 3.3V.
So it's recommended to use a debugger...
Hi
I am attempting to add nrf_crypto functionality to the example uart ble peripheral project via SEGGER Embedded Studio on MacOS.
I have opened the project options and...
I have two devices, one is a beacon (DEVICE #1) and the other (DEVICE #2) collects information from the beacon. I'm advertising with a transmit power of 4dBm. I want to reduce...
I have previously had success with programming the nRF51 Series using the nRF51 DK and want to use the nRF52840 DK to program a nRF52840 that will be run in High Voltage Mode...
From the cmakelists of bootloader in Meshv320src, I found the code "create_hex" but this code cannot found in CMake's document. How can it work to generate the hex file?
I am using SDK 15.3 and wanted to ask that if there is a while loop where I can check flags and increment tickers. The program at the moment gets stuck inside
Suggestions...
