Hello. I am a beginner and I have a nrf52840 Dongle board. I tried to use the interrupt from TIMER0. I defined the timer and it works correctly, but when I enable the interrupt...
Hi, We're in the product validation stage of development with nRF54L15, part of the validation is temperature cycling, we noticed that devices seem to be "stuck" in sleep...
Hi,
I am trying to configure an Xiao Seeed Studio nrf54l15 sense to transmit pre-processed sensor data via BLE extended advertisements. As the payload is more than 251 bytes...
In this post mentioned: "Maximum theoretical peak data rate is 3.4 Mbps when transmission is scheduled into packets of 4 slots using MCS4, and these 4 slot packets are transmitted...
I want to use a new source LF clock to raise the precision from +-250ppm to around +-20ppm. I already have an oscillator mounted in my PCB, so I want to use it for BLE. I...
Hi,
I would like to know if its possible to run Azure FOTA functionality w/o using Partition Manager (aka `SB_CONFIG_PARTITION_MANAGER=n`) ?
Trying to build this gets...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
What are the best practices when processing BLE GAP scan events to avoid multi-threading issues?
I programmed the nrf52832 to successfully read BLE GAP events coming from...
I'm having trouble getting the Bluetooth Low Energy desktop library ( https://github.com/NordicSemiconductor/pc-ble-driver/tree/v4.1.1 ) set up on my Mac. My problem is occurring...
I would like to know what is the maximum ADC sampling frequency for transmitting data over Bluetooth to PC.
I am using two modules having an nRF52832 for each module....
Hello, I think there is an error in ble_advertising.c (SDK 15+).
Line 608, the code is trying to set the secondary phy but checks if the primary phy is valid ( ble_adv_primary_phy...
Hello,
I am very new to evaluating the nrf52-dk board, so I hope this is not too much of a trivial question.
I was trying to enable logging via UART without having to...
Hi
Currently I have a firmware based on template project for nrf52 (sdk15). I am interested in broadcast data, hence I used ble_advertising_advdata_update() in order to...
Hello! I use a 32kHz quartz resonator and I want to interrupt the program after 1 second with a watchdog timer. But when writing to it, 128 I get not 1 but 1.25 seconds. What...
Hello,
I followed the getting started guide but the kit can't connect. I'm getting this error:
net_if.net_if_init: There is no network interface to work with!
Is this...
Hi there,
I have a question NRF52840_PCA10056 and its SDK is latest nRF5 SDK.
The scenario is below:
The NRF52840_PCA10056 build a connection with a smartphone like...
1. It is understood that zigbee3.0 certification requires Green Power, but I did not see the definition and use of Green Power in the example. How does the nordic zigbee pass...
Hello Everyone,
I am trying to compile zigbee_light_coordinator example. I have my path included as ../../../../../../../external/nRF-IEEE-802.15.4-radio-driver/src in make...
Hello,
I have accidential removed the DFU bootloader on my PCA10059 dongel..... is there an image that I can write to the dongle to get it back into its out of the box condition...
Hi there, I have set my SAADC to have an acquisition time of 3us , however when I toggle a pin before and after calling
nrfx_saadc_sample_convert
I measure the time of...
The sample project is "nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\experimental\ble_nfc_pairing_reference"
I think "micro_ecc" is a normal build.
Please check attached...
