Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
I would like to use the beacon example to send some manufacturer specific data over BLE.
I am using the nrf52DK , nRF5_SDK_14.2.0_17b948a and s132.
My question is other...
What's the fastest scanning settings for connecting to anywhere from 1 to 20 peripherals at a time? My peripherals are all advertising at 211.25ms. I won't be sending any...
Hi,
I am trying to use an SAADC converter to measure voltage in range from 0v to 3v5 but I cannot succeed. It is not possible to measure a voltage above 3V1. Well at least...
Hello, community.
I'm using NRF51822 SoC(256KB ROM, 32KB RAM) with S130 Softdevice.
I'd like to reduce the rom size and the ram size to decrease the production cost. ...
Hello,
I am using nRF52840 DK for bulding a bluetooth mesh. I would like to use JLink in board kit to flash and debug for other nrf chip.
How I can connect and configure...
Hi,
I'm using SDK 15.3. How do I connect a central (nrf53832) to another central (phone/laptop) using multilink central example? Its only connecting to other peripherals...
Using the 15.2 SDK, the stack generates an error when attempting to bond. I am using the android nRF Connect test app to initiate the bonding after connection. The error generated...
I'm using SDK 15.2 & HID keyboard example. I would like to know the following things-
1. How long does BLE chip advertise its name before making a connection with central...
Hello,
We're currently preparing for BLE certification of our device. It contains an NRF52840 on a custom PCB, so I believe we'll need to perform RF-PHY testing for certification...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
Hi! I develop board based on NRF52832. P0.08 is connected to the MOSFET transistor.
The transistor switches the relay. During start (power on or reset) on GPIO there is...
Hello,
Please let me check about the usage of an IRK for the default setting and how to change an IRK each bonding cycle.
We use the resolvable address for our application...
Hello
I have a setup with 3 nrf6310 dev kit and with a nrf24LE1 module on each of them.
1 acts as a transmitter and the other 2 act as a receivers. What I specifically...
Hi
I am using nrf52 DevKit and was able to load the \examples\ble_peripheral\ble_app_beacon program on it. I am able to see the beacon RSSI, major and minor values. Now...
