Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hey! . I am new to embedded developing and was trying to familiarize with nrf52 DK .
Issue : When i try to run the BLE examples in sdk after clicking " download and debug...
Hello! I am having issues dfu from the huawei p30 lite. with nrf51. Tried with nrf connect and nrf toolbox.
Dfu progress stops at 2-3% when uploading. Error Remote dfu error...
I am unable to connect the nRF9160DK to the cellular network.
I have gone through the "Get started guide" (working in Linux) and I have been able to install the SDK. I have...
Hi, we have faced with the same issue as many nRF52 users, debug interface (DIF) will stay active after flashing and high (~3mA) continuous current remains, Power cycle will...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
In BLE peripheral example ‘ble_app_template’, it is for doing Advertisement...
hi... folks
I am working on multilink central example, i have modified this example to multi link central uart ,where i can able to connect to multiple peripheral to a single...
Hi,
I am using NRF51822(PCA10028) ble_app_uart example , I need to change the name of the BLE device during Advertising and store the name in Flash so that when ever the...
Hello,
I am trying to establish a network to send data over the boards.
I tried using examples in Ble_central and Ble_peripheral, but in those examples they would stay...
Using the esb tx fifo, it appears to change the ESB_MODE from PTX to PRX, and changes the esb channel to some other value. Is there any way to setup the radio so that it doesn...
Hello,
I am working with nrf52840. I have read how the SAADC example works at https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v13.0.0%2Fnrf_dev_saadc_example...
Hi everyone, I'm having trouble deciding on the "best" / "most sane" way to interface two I2C sensors with the nRF5832. Both sensors are on the same I2C bus. The first sensor...
Hi Bro
I have a project need to use BLE + ESB Concurrently, actually I have did it in my previous project
but seems it has problem in new SDK
In my old project: SDK11...
I'm using the nRF52 DK (with an updated firmware) to program an external target (using the "Debug out" connector). It looks like the programming speed is limited to 1MHz:...
