Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hello
I am using SDK15.3 and nrf52832 development board.
In my setup,
1. I have a few peripheral nodes whose only job is to transmit some arbitrary packets ( say P)...
My setup consists of a Raspberry pi and a PCA10056 dev-board (NRF52840). I followed the instruction from here in order to set up the Raspberry pi as boarder router and connect...
Hi all,
I am working on the Smart remote and when "spamming" a lot of key simultaneously, I sometimes get a warning "m_coms : packet lost" and then a disconnection.
...
Hello,
I have a Taiyo Yuden EYSHSNZWZ module. I also had a breakout board manufactured for it to get access to all the pins. I am having trouble trying to program the...
Hello,
I`m trying to get this ( https://github.com/NordicPlayground/nrf52-ble-multi-link-multi-role/ ) working properly to test the possible working range between two nRF52840...
To the kind attention of the Nordic support team,
Hi to you all, I have got legacy gazell code running on nRF24. In old code the following instructions was used:
hal_nrf_set_address...
My customer wants to do a range test with a propritary 802.15.4 software.
Do you have an example for the nRF52840DK with an blinking led if the communication is established...
Hello,
i want to display a string in 5x21 led matrix using HT1632 Led driver
Using SPIM0 Protocol i should send data from nrf52832 to HT1632 led driver
My question is...
Hello,
I am working with the mesh SDK 2.1.1 version and the Light switch proxy server and proxy client examples.
Everything is working fine between client and server...
Hello,
We are designing a board based on nRF51422 and we are working with a company based in a different country for Android/iOS app development. They bought a nRF51 Dongle...
I have downloaded the latest nrfgo, but the version of jlink is 5.12V.jlink5.12 does not support nrf52840,so i updata it to jlink6.40,however nrfgo still can't download the...
Hi All,
I am Using the NRF52840 DK Device for my application development
I want 2 UARTS for my application
I have used the example - nRF5_SDK_15.3.0_59ac345\examples...
I am currently developing a central device based on the NRF52832. I am able to discover and get handles to all the services and characteristics of interest on the peripheral...
Hello,
I wanted to know if I can use AT commands to communicate with nrf52840 DK.
If it is possible, do I need to have a separate firmware or is nordic sdk enough?
