Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hi, i am learning with thingy 91 x and nrf9151dk. I made the online courses and succesfully conect to the cloud with the nrf desktop quick start in both devices. Now, i would...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We have an application running on a custom board with the following configuration:
nrf52832
SDK v12.3
Softdevice S132 v3.1.0 and S332 v2.0.0 (different variants of PCB...
Hi, I am using nRF51822 now,SDK11.0, how to let the peripheral open the peer's notification, My original design uses DA14580, Android APP can receive messages when the peer...
hello .
i am trying to open driver in the advertising.py example pc-ble-driver-py-master
driver.open() and this line throw exception
if err_code != expected: raise NordicSemiException...
It seems nordic devices can not be programmed without certain segger software.
In order to set up my toolchain, I had to install SEGGER Embedded Studio IDE (although i dont...
I have seen nordic contains QDID 111537 for mesh profile subsystems. Is this profile subsystem includes the Mesh Model or nordic have a plan to get Mesh Model QDID seperately...
Hi.
I'd like to disable retransmission in my Thread application built with SDK for Thread and Zigbee 1.0. I followed the instructions from Infocenter "Building the latest...
Hi @all
I'm searching for a nRF905 breakout board for the 868Mhz band. All I can find is nRF905 boards for 433Mhz (e.g. rfinchina or freqchina). Anyone tips where I can...
I'm trying to pair a Nordic SDK15 central to a non Nordic peripheral ( BLE 4.0)
I have no IO for passkeys
I'm testing by pairing Master control panel ( is it BLE 4.2?...
Hello team,
Having a bit of an issue. The link for the S140 SoftDevice results in an "Access Denied" page.
Origination Page >> https://www.nordicsemi.com/eng/Products...
Hi Everyone
I am able to configure BLE on the template project and it is sending data from nrf52840 to BLE nrfconnect app using the function nrf_ble_data_send() .
However...
HI All,
I am trying to upgrade sdk v11 to sdk v13 in my project and after compilation i am facing Linker Error as mentioned below.
binaries/app/SmartTag2/dfuFlash.c.o...
Hi :
I have the same problem. I try to flash program to the Dongle using MCP. Every time I program the Dongle, the MCP log report: "NO response from master emulator". What...
