As in subject, psa_aead_finish function generates incorrect tag for AES-GCM when Nordic proprietary library is used.
Works fine with Oberon backend.
Similar problem reported...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
NCS: v3.4.0 Board: custom board based loosely on PAN1783 TF-M not used
Images: - App core: mcuboot, Firmware (main app) - Net core: b0n, ipc_radio
Summary of configuration...
I've noticed that if I have data queued to go out over the uart (using app_uart_fifo) if I do an fds_record_update the UART TX is effected. You can see what's happening in...
I have put my code developed on a nRF52 dk on a custom board that is based on a ISP1507 CPU. We are having higher current consumption than expected, I use the exact same code...
Hi There,
In company we are working with nRF8001 (currently C revision) and we want to send some custom data in an advertising packet. However, when C revision is selected...
From the S132 5.1.0 specification, I expect that its RAM usage should be only 0x1228 bytes plus ATTR_TAB_SIZE. However, when I compile two of the example projects using IAR...
I am working on a project in Nordic SDK 8.1 that requires using a timer. I am confused where I need to define the timer though (using APP_TIMER_DEF). If I put it right after...
I am working with the SDK 12, nrf52832 low_power_pwm example. I am concerned about the power consumption I am measuring.
I am trying to produce a 1khz PWM for an LED (the...
Howdy,
I am having difficulties writing to NVRAM (reading appears to be fine and is reporting 0xFF's everwhere). I am using a rather old SDK and SoftDevice 110 (version...
How much is the nRF52840 USB DP/DM pins impedance in transmit mode?
There is no info in datasheet .
On the PDK board there are 39 ohm resistors connected in series with...
The engineering B errata mentions PAN 186, that the current consumption in System ON Idle is increased if High-Voltage mode is used. Is there any information available how...
Hi everyone, I'm having troubles with a project using softdevice, and I think it could be a memory problem, I just wanted to confirm that the addresses are correct and there...
Why was this removed? The SD 3.0 docs show only random static and public as options and I get bad address for the others which is consistent with the docs. We were using random...
Hello
Nordic Team.
I controling nrf spi.
testing for example nrfSDK14.0.0\example\peripheral\spi\pca10040\blank\arm5_no_packs\spi_pca10040
/**
* Copyright (c...
Hello everyone, I want to run project ble_uart on NRF52832 in Keil.
At the beginning of the main.c I add
#define BOARD_NRF6310
But get error
C:\Keil_v5\ARM\PACK\NordicSemiconductor...
