It flashes with sucess
C:\Users\vasco>openocd -f interface/stlink.cfg -f target/nrf52.cfg -c "program \"C:/Users/vasco/OneDrive/Ambiente de Trabalho/zephyr.hex\" verify...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hi, I want to run Bluetooth Mesh Light example on nrf54h20 chip.
At the beginning I prepared devboard with this tutorial: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hello,
Is there a way to test packet corruption? My setup would be that I have my FW in nRF52-DK. Then I would test communication using nRF51-Dongle. I would like to force...
I want to connect two nRF51822-BKs and find their proximity. If one of the beacons go >5m away from the other beacon then one should beep/LED ON.
What is the best way to...
I have some troubles to understand the system clock functionality.
I am using a Module from Rigado which uses the nRF52 and has an external 32Mhz osc. on board.
In the...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
hi
i didn't manage to find detailed requirements on the voltage from the chip.
in the spec i see voltage range of :1.7-3.6v
but its not enough data for designing converter...
hi everyone, I am new to developing apps for nrf51822, and currently I want to learn first, I tried to google a lot around and could not look for the right resources, it would...
hi,
I would like to connect hid keypad with ipad,phone5s and android phone(all these have Bluetooth version 4 )but i couldn't connect this.ie, The nrf51822 module advertising...
I attempted to capture a waveform when running the SPI master example on nFR52 SDK/PCA10040. The source code I have as default and showing as follows
#define SPI0_ENABLED...
Hello,
We are working on a project that includes a countdown but we could not able to do it. Simply we want to do this:
Nrf51822 receives a signal-->run our funcion...
Recently, I've built up the latest OpenMesh v.0.85 example among 3 pieces of nRF51DK successfully. For my application, I would like to increase the data payload, is it possible...
Hi,
I am using Gazell for communication between two nodes. The first node is sending a sensor reading to the second node (which will be called henceforth the sink node...
Hello everybody
I have a nRF905 circuit sealed in a different medium than air and I am facing an 8 dBm power loss after sealing. I would like to know the following: Is...
Hi
I am using PhoneGap Build with BLE plugin to develop iOS/Android APPs for nRF51822 , it is a easy way to develop a BLE APPs by JavaScript. Unfortunately, I can't find...
Hello,
We have recently been playing around with the NRF51822 Beacon and we liked the way it works. So there is one thing we are very curious about: is there any cheaper...
As the followup/implementation to this question
I want to implement a multirole application for the PCA20006 (rev 1.2).
Currently I will only need advertising for my data...
