Hi,
I have an issue with VS code. The connected devices does not show my jlink debugger nor the DK. However, nrf connect desktop programmer shows them.
Toolchain: v2.6...
Hi,
I'm developing custom firmware on the appcore and netcore. The netcore runs BLE controller, as well another custom IPC service to communicate between the appcore and...
Hi everyone,
I’m working on a project involving the nRF7002DK, where I’m trying to combine two separately working applications:
A TinyML CIFAR-10 image classification...
Hi,
we are looking into incorporating a NRF52 module into our control units, but to allow extending the antenna position away from the case through male-female SMA cables...
I opened up the nRF Connect for Desktop application and noticed a new version for the SDK , 3.0.0. I also noticed that the application is being deprecated.
Inside of Visual...
Hi,
I am trying to use nfc_t4t_lib and I have some issues because processing incoming data takes some time (around 100 ms) and therefore sending the response occurs late...
Hello Everyone,
I try to develop Nuvoton + NRF24L01 SPI communicate each other. And I don't understand why MISO bus has 0x0E after I send Write_Command 0x20?
void NRF24_AdressTX...
Hi,
I need to implement 51822 drirver, is there some demo for that. By now I don't decide wich oled to use, and I don't know how many type of OLED at all. I wish a oled...
Where can I get a copy of the nRF52 Reference Manual?
The nRF51 Reference Manual is here:
www.nordicsemi.com/.../nRF51_Series_Reference_manual v3.0.pdf
Where can I...
i am programming nrf-51 dk's program.
i have to get data from sensor, so i am studying example code which is twi_sensor.
i don't know well these function.
nrf_drv_twi_tx...
[hide preview]
.
I am looking for a detailed description of the Memory Protection Unit for the nRF51822 as described at a high level in nRF51822_PS v3.1.pdf.
I know...
Dears,
I have tried the example code of PWM function at nRF52 DK(PCA10040).
It worked with a 2V DC level. Is there any mistakes or something wrong? Why a DC level...
I use the SDK v11.0 alpha, the S130 with my USB-dongle(NRF51422).
I use the low_power_pwm to initialize 4 different PWMs. I used the Example low_power_pwm_s130_pca10031...
Hi,
I have a problem with pwm,
I am using keil uvision 5.17, SDK 9.0.0, SD 130, nRF 51822.
I have programmed the code which can control servo motor(SG90) by smartphone...
I'v read the Arduino SDK for nRF8001 (and Poring ACI to any other microcontroller)
some questions:
1)the source code is complicated and there is'nt enough comment on that...
Not sure if forums or MyPage support requests are better for this.
It seems NRF_LOG has taken a step backward from what was used in the previous nRF52 0.9.2 SDK. What I...
hello there . i want to get i2c data on ble advertising packet
int main(void)
{
uint32_t err_code;
bool erase_bonds;
ret_code_t ret_code;
int16_t x_val;
int16_t...
Hi, I have PCA10036 board v1.0.0 and I would like to run sample projects from nRF5_IoT_SDK_v0.9.x that are by default designed for PCA10040. Do I need to make any changes...
hi. I want to work with nRF8001 by STM32F103 family from ST.( www.st.com/.../LN1565) is there any one who develop a project with STM32F103 by using STM32CubeF1 ( www.st.com...
hi,
i am using nrf51822 s110 sdv 7.1.0,when i upgrade the soft device, application and boot loader(create .zip) using the nRF toolbox application. application shows me...
