Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Are there any migration guides for a customer who wants to migrate from nRF5340 to nRF54L15? And if they are nRF54L15 in chipscale, anything they should be aware of including...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hello Nordic Semi,
After being in production of a battery powered remote control for over a year now, we have found many batteries going flat in the field. I have been...
In my test, with the same configuration, ANTWARE II always searches much faster than nRF51422 software.
For example. I have Master channel and Slave channel set up at 4Hz...
The test code:
#include "nrf51.h"
int main(void) {
NRF_CLOCK->LFCLKSRC = 0UL; // Internal 32kHz RC
// Start the 32 kHz clock, and wait for the start up to complete...
Hi,
I have downloaded "mastercontrolpanel.3.7.1.8567.x86.msi" and try to install on windows xp of my intel core2 laptap. But it failed with prompt like "not a valid windows...
This question devzone.nordicsemi.com/.../ reports the fact that the driver cannot be used twice without manually pin reseting teh BLE dongle.
But there is another problem...
Hi Team,
I am using nRF51 DK as packet sniffer to sniff packets between Mobile and other device.
Why it captures only advertising related packets?
After successful connection...
Hi there,
If I try to store a global variable in flash I can't store it. But when I declare this variable in the main function I can store it in flash. Can someone tell...
Hello all,
I saw their was a new update for the nRF518-SDK and I was wondering how I should update this in Keil. Is this just a simple replace folder? Replacing:
...
I inherited an ANT/BLE nRF51422 project a couple of weeks ago.
It used SDK v6.1.0 and S310 SoftDevice v1.0.0
At the time, I'm sure that the SoftDevice download said...
I'm attempting to troubleshoot problems between dev teams. One team is having some issues & I notice that their binary is slightly larger when built from exactly the same...
I am trying to use the laird BL620 module not for the smartBasic, but to run my own firmware.
I have just set it up, connected to my old segger JLink debugger.
In Keil I...
Press the Connect button on the Smart ponaep NRF Uart V2.0 recognizes the page reongil signal
Disconnect state, allow to boil for your smartphone to wait about 20 minutes...
I am pretty new to the nRF51822 in the firmware side. I have been doing hardware design for many years but need a little help getting started with firmware.
Does anyone...
When the bootloader in SDK 8.0.0 checks whether the application is valid, it only computes the CRC for the application if the CRC in the bootloader settings for that bank...
