hello! I'm having problem when trying a repairing after clearing the bond information in the nrf52840 i using pairing via oob , i exchange oob between nrf52840 and RPI using...
Hi, I use the hci-uart sample (4.3.99) on an nRF54L15 board. The host is an esp. The setup seems to work fine, but every now and then the Nordic board gives an assert:
ASSERTION...
Does the EdgeAI module support running multiple models in parallel? For example, an anomaly detector running on one data source and a classification model running on a second...
i would like to implement multi pairing connection of 20 peripheral device by single central mode. Is it best solution to adopt multi NUS sample S/W in GIthub?
Hello,I am working with the nRF9151 SMA DK and I need the VDD_GPIO rail to operate at 3.3V to interface with some external components.
According to the schematics, VOUT1...
Hi,
I want to download FOTA-updates with HTTPS from a function app running on Azure. I am not using IoT hub or MQTT. I'm using modem firmware 2.0.4 in combination with version...
Hi,
In our PCB using the nRF54L15, we used different P2 pins for the sQSPI, believing after reading the docs and driver API, that one could configure different pins than...
I'm trying to backport the code form SDK 9.0 to SDK 7.2,
but i need to make sure that can be supported.
I found the "ATT-51", and there is a table about that,but the last...
ble_dtm.c has some bugs related to signed integer representation which prevent negative power (less than 0 dBm) from being requested in the vendor specific message.
...
Hi, all.
I'm using "SEGGER_RTT_printf" for debugging. Because have no uart port on my development board.
I want print double type variable like below.
double pi...
I am currently trying to communicate with a GPS module using the UART on an nRF51422 (using the Dynastream N548M5CB module). I am using SDK v9.0.0 and the FIFO version of...
Hi,
I want to send a continuous stream of data very quickly into the nRF51 through SPI and then dispatching it to a smartphone via BLE.
However I keep getting BLE no...
Hello
When i am in keil uvision 5.18 and use the pack installer all the examples using Softdevice S110 are gone in Keil. Is this a known issue and is there any way to solve...
I followed the instructions and comments in devzone.nordicsemi.com/.../ . I built a project around the ble_app_gls example (with a couple of minor changes such as using -DNRF_LOG_USES_RTT...
Hi, I would like to program nRF51822 flash over SWD interface. I have another micro LPC1100 series that has the flash image for RF51822 and connected to nRF51822 over SWDIO...
Hi,
It is written in the nf_drv_uart.h file for nrf_drv_uart_rx_abort() that
If Easy DMA is not used event will be
called from the function context. If
Easy DMA...
Dear All,
We work on the NRF52 CSP revB. We have a board with two external crystals (32MhZ and 32kHz).
When we use the example program with BLE and UART, it works great...
Hi,
How can i get time stamp from RTC1 timer? While i am using app_timer + Softdevice?
Or any other way
Thanks and Regards,just to get timestamps from timer?
Faizan...
Hi,
I added DFU function to the example of ble_app_hids_keyboard according to ble_app_hrs_dfu.uvproj.
Test environment: nrf51822_xxAA, SDK_v6_1_0 and S110_v7_1, before...
Hi all,
I would like to use Pstorage module. Since flash endurance is 20.000 write/erase cycle, I need to use it very efficiently. If I use pstorage_update function it...
Hello,
I am quite new to Beacon development. I am trying to use the examples of NRF SDK 10.0 on the NRF Beacon. I would like to "install" the application via OTA. I tried...
