Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
Hello,
I am creating a PCB design for NRF2402AG but I'm not sure whether I should connect pad under the NRF to the ground or I should left them isolated. I could not found...
Hello
I get this error when I try to program the module:
Parsing hex file(s).
ERROR: Cannot find C:\Nordic Semiconductor\nRF51 SDK_v6.0.0.43681\Nordic\nrf51822\Board...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
Hi dear friends from Nordic Semi,
I´m in great trouble trying to make these nRF24L01+ to work, one unit as a transmiter, and one unit as a receiver, it can be to send 3 bytes...
Hi,
I am using nRF51822 Evaluation Kit along with keil uvision4. Will using optimization in keil IDE make any problem in the normal working of BLE project? Will it affect...
Hello All,
We need to design a Remote Control based on NRF24LE1 working with mercury cell.
So they key factor is hardware & software optimisation for the lowest possible...
Is anyone aware of any of these on the market yet? I know of one, from Insight SIP, but am keen to hear about any others.
(This would save space on the PCB, simplify our...
Using twi_sw_master have discovered that the nrf51422 E00 draws 1.3mA in off mode.
When the twi device is removed from the bus, the nrf51422 draws under 5uA in off mode...
I want to merge soft device, application and boot loader in order to improve efficiency for factory. I searched relative topics in this forum and found something useful. At...
We have been unable to establish a link between a Garmin HR monitor over the air, we have established USB comms to a cell phone device. We took the transmission line directly...
i find one related question:
devzone.nordicsemi.com/.../
and this is refers to nrf8001,
so, i wonder if nRF51 could share both crystal with other MCU?
please help to...
Hello,
I am trying to test ble_app_uart example code and replicate similar behaviour.
I have disabled hwfc. But without hwfc, UART0_IRQHandler is not getting called...
Hi
I need to implement I2C slave side (up to 100kBit/s) on a nRF51822 chip. As far as i see the inegrated TWI peripherial only supportes the master side. Any ideas how...
I just received an nRF51822 eval/development board that has a sticker on it that says "PCA10004". I also just downloaded the latest SDK (nrf51_sdk_V6_1_0).
As far as I...
