I wrote a simple terminal that reads the keyboard input from USB UART device and echos it back to the same device. It works as follows: 1. It registers an interrupt handler...
Hello,
I using ncs v3.1.1 SLM on nrf9151 to send messages to a CoAP server. It seems nrf9151 by default uses AES_128_CBC_SHA256 even though on the server side, we have given...
Hi, I am unable to read GPIOs (always getting 0x00000000 from gpio_port_get or 0 from gpio_pin_get). My main project is https://github.com/marcuswu/leaf-fall/tree/main/firmware...
The DECT Nr+ shell (the MAC version, not the -phy; tested with v3.3.0-ba167d9f3db4) offers IPv6 connectivity.
The DECT standard has a profile for IPv6 described in ETSI...
Hello,
Overview:
Currently we are using nRF9160 we are using mbedtls library for generating EC key based certificates (self-signed and CSR). Our code is built with TFM...
Hello, I wanted to update my project (Custom board using the nRF54L15 ) to the v3.3.0 SDK since this fixed a BLE bug with the v3.0.1. version. To my knowledge I did not change...
I have installed ncs3.3.0 and want to keep ncs unaffected. According to the document docs.nordicsemi.com/.../sdk_setup.html , I should choose to import the edge impulse SDK...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
If I write a zero to the output register, and enable the pullup on the same pin, can I switch between driven low output and input with pullup simply by settting/clearing the...
Hello,
For our DFU solution we would like to read the current hardware/software revision of the module. But now we can only test the hardware/software revision of the application...
Dear All,
I can read two different ANT sensors sucessfully with my target system, but initialization of sensors only works first time. When changing sensorIDs of simulator...
HI, All.
I have some troubles:
Why MBR is erased when I erase or write the SorfDevice with 1kB at address 0x3000? My SorfDevice version is 7.1.0.
Thanks all.
Update...
Hello all,
When I try to implement the new watchdog driver it keeps saying that the NRF_DRV_WDT_DEAFULT_CONFIG is undeclared. What am I missing I have all the requered...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
hello,
In order to develop a project on master-bridge-slave,i found scan_start() in the ble_central program.But the function definition for sd_ble_gap_scan_start() in scan_start...
I am using nRF51422 SDK v8.0 and the board for evaluation is PCA10003. As I am using the BLE in GENERIC_KEYRING. The same I am trying to configure to send Immediate alert...
Hi,
I'm wondering if there's any way to check if a peripheral device was actively scanned? I can easily set my own scan response data but is there any message generated...
Hi all,
As i understand from useful discussion here, we can send one 20 bytes packet per connection when we use S120 to S110 direction, and this number could be increased...
Hello,
Working on my own code to integrate an arm chip with the nRF8001, after I read the device status, which says it's in Setup-mode, I'm sending the setup configuration...
Hi,
I want to know how sd_ble_gap_rssi_get API works? Is it send any BLE packets over radio to get RSSI whenever application calls this function. What are the sets of events...
