When transitioning from ncs v3.3.0 to ncs v3.4.1 noticed a warning about CONFIG_BOOT_ECDSA_CC310 being depreciated when building MCUboot. The release notes suggest using PSA...
Hi everyone! I'm having difficulties in setting up a little project in which I want to pass I2S data over USB. I know I'm using the old USB Audio Class endpoints, but everything...
Hello,
Thank you for your help.my questions are as follows
SDK : ncs 3.4.0
Hardware board ：nRF54L15
Based on the ncs SDK 3.4.0, how should one set the MAC address...
On a custom Zigbee End Device application for the Thingy:53 (NCS v2.9.3), ZCL Configure Reporting commands sent by Zigbee2MQTT are rejected with ZCL status FAILURE for almost...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
Hello, I need to scan the advertising data of my peripheral wich advertise with extended advertsing and LE coded PHY.
I use zephyr 3.7, and I work if I use the BLE controller...
Using Modem FW 1.3.6. Using NCS 2.6.0.
We're experiencing an issue in a test setup where we are getting this error reported (528) when trying to clear/set root certificates...
Hello nRF Team,
I am developing a ble terminal app based on the Bluetooth: Peripheral UART sample (nRF Connect SDKv2.7.0) on nRF52840DK. I was testing the app BLE pairing...
When following the unit test example, and even with an alternate minimal implementation, I get the following error:
PS {nRF Connect terminal} > west build -b nrf52840dk...
To people who might be interested in this ticket
I'm trying to make a WiFi connection using the nRF7002 chip. It is a custom board based on STM32 chip. My question is, is...
example:ble_app_uart+ esb_timeslot SDK17.1 Hi Recently our product (PRX) received poor esb communication. I caught through sniffer that when PTX sends a message, our device...
Hi, I have gone through Lesson 4 in Wifi fundamentals. But exercise 1 fails to compile. I have also tested to compile the solution-project, but with the same result. There...
When I look at eh graphic .overlay, I see that the UART0 is there, but no node is assigned. Is there a Node for a two wire UART Driver with no flow control? Peripheral only...
Hello,
I bought a new USB keyboard and since i can't detect anymore Nordic Devboard as nRF5380. No device detected on Visual Studio Code, and on nRFProgrammer neither. ...
Hi,
I working on a project where i measure the distance between nrf52840 dongle and nrf52840 dk using multi carrier phase difference method.
Now, i want to display the...
Hello.
I'm currently trying to send AT Command using an external MCU or USB to UART to check LTE on the NRF9160. The board I use is the nRF9160DK. I changed the pins of...
HI,
I have two solar panes for my project 3W 5V and 2 W 9V. I would to measure current of the panels with the Power Profiler II.
I think this should work (my calc is 3W...
Good Evening!
We are designing a project using BLE; however, it requires quite heavy processing. We are still at a low level with pure C to save power, but the MCUs offered...
Hello,
Looking for potentially a better way of un-provisioning a provisioned mesh node. My nodes are provisioned via NFC, tag data containing UUIDs & OOB data. After the...
I work nRF52840 + nRF5 SDK(S140 v7.2.0)
If I call sd_ble_gap_connect() for a DeviceAddress of an already connected device, what will be the result?
What will be the error...
