NCS 3.4.0, nRF91, no SECURE_BOOT, no nordic,pm-ext-flash.
There is a bug in selecting the UPLOAD_FLASH_AREA_LABEL, see my ticket in the zepyhr project.
That was unfortunately...
Hello,
I've applied 5V to the anode of the LED, and the cathode is connected to the LED0 terminal of the nPM1300 via a resistor.
I've set the registers in I2C as follows...
I am using the nRF52840 dev kit, I have setup nrf connect sdk v3.4.0 and v3.4.0 toolchain, signed up with ANT and added ANT to my west yaml file. The first issue I had was...
we run long-term HIL tests with typically 3–8 nRF9151 DKs:
DKs spaced only about 1–3 cm apart
short USB 3.x cables to powered USB 3.2 hubs directly below them
sometimes...
Hi
Our project uses the nRF52833 SoC without an external PA. During the Korea KC spurious emission certification, the out-of-band emission on the first channel in DTM 2...
Hello,
I have been chasing this problem for some time, but it has been difficult to capture.
The issue occurs when the device is sitting idle (no eDRX or other power-saving...
Hi,
1.What is the maximum rate that the QSPI of nRF54L15 can achieve? 2. Is it possible for me to use QSPI to read the flash memory while simultaneously refreshing the screen...
I am programming now nrf52810 I try to merge uart functionality to ble_app_blinky project but it does not work i debug and found out uar_error_handler() never been reached...
Hi.
I am using a custom board on the nRF52820 microcontroller (wiring diagram in the figure). When the microcontroller is powered only from the battery (via external LDO...
Document: HTTPS_SAMPLE_2024_09_19T02_55_15_089Z.txt I was programming the HTTPS sample with default parameters. I managed to connect to "example.com successfully". I managed...
I'm working on a BLE project based off of the peripheral_lbs sample within the nRF Connect SDK v2.7.0. I am attempting to increase the BLE security level up to either level...
Hi,
I am working on a battery powered device that collects data, save it to files and go to sleep, when it is not connected to a laptop via USB. When connected, the device...
Hi,
I want to change the LED pin that blinks to indicate BLE advertisement to pin 6. I have changed the LED_1 and LED_STOP in pca10040.h to 6:
I have also set NRF_LOG_BACKEND_UART_ENABLED...
Hi.
I am developing a custom board using nRF52840 inside a Moko MK08A and an accelerometer LIS2DH.
My circuit has a 3V3 voltage regulator just for the LIS. The microcontroller...
Hello
I'm trying to connect muy Power Profiler Kit II to my PC, and when I choose the device from the list it pops-up:
I clicked 'Program' and after I supposed it...
Hello,
I'm trying to access active PCO from nrf9160 applicaton to be able to diagnose problems like missing DNS, wrong access point etc. I tried using %XPCO command, AT...
Hello.
I am developing device using nRF52840 and i have question about analog pin usage.
My circuit is analog Pins getting voltage supply while nRF52840 is not used...
Hello Nordic team,
how is it possible to perform Packet Error Rate testing during an active OpenThread connection between two nRF52840 devices? The requested test scenario...
I am working with an app developer that is having trouble getting the DFU to work with my zephyr application. They are using:
https://nordicsemiconductor.github.io/IOS-DFU...
When I was considering the layout of the nRF5340 chip, I found that the pins of the nRF5340 chip are very small, and I need to punch the vias on the pads, and then use the...
