Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
What I'm working on:
I'm working on a small project using this nrf52840 module:
www.minew.com/.../
Access to source:
If it helps to understand my issue, all the design...
In the function "bt_scan_filter_status_get(bt_filter_status *status)" [file: subsys/bluetooth/scan.c #1302], the variable
"status->manufacturer_data.enabled" is not updated...
hi devzone
I've trouble starting nRF Connect for Desktop v3.12.0.
I'm using nrf52-dk / pca10040 board and nrf5_sdk_17.1.
when I run the program "nRF Connect for...
Hi,
I do have a question about PCB layers. I did read it is better to use a minimum of 2 layer PCB, but why is this? By example is a single layer also OK?
I'm trying to...
Hi Team,
We are using Nordic connect SDK nCS 1.9.1 & nrf52833
currently have not changed any clock frequency they're at default settings, we want to know what is the...
Hi, quick question.
Software: SDK 17.1.0 with segger embedded studio
Hardware: nrf52833-dk
Background: I read that it is possible to take iq samples of the payload....
Trying to using IEEE-802.15.4 on nRF52820 with SDK-17.1.0, Librarie 802_15_4/raw/802_15_4_lib_gcc.a.
nRF52820 n ot support FPU so set -mfloat-abi=soft in Makefile
Encounter...
I successfully completed all exercises from DevAcademy using nRF Connect SDK v2.0.0 and nRF Connect SDK v2.1.1.
However, when I tried to experiment with DevAcademy Lesson...
I have not done anything with the SDK for a while so I updated Segger Embedded Studio to the latest: 6.40 and the latest nRF SDK 17.1.0 and built my project and I only needed...
Hello together, I'm searching for a way to go I max low power mode possible an then wake a from one of three reasons:
Timer/Clock
NFC-Field
GPIO
I searched the...
I have an application setup to use RTT for console and logging whereas UART is disabled. If I enable the UART async API then RTT stops working.
Working:
CONFIG_ESB...
Hello,
I tried to run the llpm (low latency packet mode) code by establishing a connection between nrf5340dk and nrf52840 devices.
I receive a transmission latemcy between...
I've been trying to get breakpoints working on a new nRF Connect project but have been running into an issue: when I hit "Debug" in the nRF Connect plugin in VSCode, the app...
The documentation here:
https://docs.zephyrproject.org/apidoc/latest/group__bt__gap.html#gae11eb8ad254418c38a0e8689df25a159
says, I can call l bt_id_create() before bt_enable...
Hi Nordic,
I am working on code which utilizes the DM library on many devices in a room. Can you please help with a few questions?
Some devices are always initiators...
