Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hello, Under Windows 11 Pro, nRF Connect SDK v3.4.0 fails to compile builds with error "CMAKE_BINARY_DIR length (109) exceeds 90 characters." The same build on Windows 11...
Hello,
Can you please provide a PCB footprint and a 3D step file for the IC for the part NRF54LM20B-QGAA-R7? This is the QFN52 package.
Can you also provide reference...
I have an application with a shipping mode that when enabled/disabled calls `conn_mgr_all_if_connect/conn_mgr_all_if_disconnect`. These functions eventually end up in `lte_net_if...
Hello,
I am using nRF52840 with nRF5SDK v17.1.0 , and I have several questions regarding DFU. Reference page: https://docs.nordicsemi.com/bundle/sdk_nrf5_v17.1.0/page/index...
I want to use the nRF5340 in Thingy:91x to control the external flash (256M bit) and pariition it as LittleFS. I can be sucessfully create partition in nRF5340DK but cancan...
Hell there Can I find an SDK that is supported on Nrf52805 chip? Or can I get any proper guidance on program of nrf52805 (the module MS46SFIi) together with Segger Studio...
Hi,
I am using the nRF54L15 and recently migrated my project from NCS v3.3.0 to NCS v3.4.0.
My project does not use the UART for TF-M logging, so I have the following...
I've built the peripheral_uart project & it works on both the nRF52DK/nRF52832 & nRF52840DK/nRF 52840
But if I enable bootlooder by adding " SB_CONFIG_BOOTLOADER_MCUBOOT...
Hello everyone! We were working with our nRF52DK boards and one of our students had issues flashing a board. He used a recent version of Segger J-Link Commander (V9.30 as...
Hi
A colleague and I are independently following the Nordic Academy Cellular IoT Fundamentals course and using the Thingy:91x as a test bed.
When attempting to build Lesson...
Hello
When following the guidline of a new way to extend boards , VSCode "Add Build Configuration" is blank. Am I doing something wrong or this is not yet supported by...
Hello,
We use the nPM2100 EK for getting familiar with nPM2100 for its potential use in our project where we aim to use single AAA battery for powering it.
Our usage profile...
NCS 3.02 54L10
I am using uart0 in async mode for printk and user input (my own callback not zephyr CLI). I need to be able to put the uart into suspend after an inactivity...
