Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
Hi all,
I am using ncs version 1.5.0 and dk version 0.15.0.
I would like to rely on the CC310 piece of hardware to perform some cryptographic computation.
However, I...
Hello.
I have a question about setting MAC address.
For now, my device uses random static address from FICR.
And I also use "bt_set_id_addr()" function for test purpose...
Hello
I'm having some issues setting up monitor mode debugging with the nrf connect sdk v1.4.99.
I've roughly followed the steps outlined in this guide , the exact steps...
Hello,
I am trying to program my NRF52840 chip with the Secure Bootloader UART project, in addition to the BLE App UART project as mentioned in the title. So far, having...
I am trying to work with Bme680 with I2C communication i can read every value but i cant read air quality value its always at 806516 value and does not change . I thing configirations...
I've been trying to integrate CLI over USB CDC ACM into my project, but I'm failing even to run the SDK example.
CLI works fine over UART, but it won't run over USB.
...
Hi,
My application has hard faults sometimes, and I'm trying to figure out the reason.
When it occurs - I have a hard fault log, but p_stack->pc is 0. I can't understand...
When I use j-link soft uart all good
but when i disconnect j-link the soft uart will error
like this so�rceid=2, status=0 sourceid=3, status=0 sourceid=4, status=0
Hello,
I'm new to BLE product and nRF52840 dongle and DK are my first BLE evaluation kits. I've some experience in Arduino AVR microcontroller. My setup is as follow:
...
Hi All,
I've been successfully using Martin's example - https://github.com/Martinsbl/nrf5-mpu-examples/tree/master/nrf52-mpu-easydma-using-gpiote-and-registers - for DMA...
I need to connect a PN532 V3 Module to a nRF52840 using SPI. I tested it using arduino IDE (I used those three libraries: Adafruit_PN532.h ( github.com/.../Adafruit_PN532...
We have custom board which is interfaced with PCA10040 board through bebug out port. Blinky example is working fine on 10040 but when I download it on evaluation board its...
Hi,
I've been following below tutorial and everything works fine.
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-characteristics...
The loader script provided to Segger for use with Embedded Studio includes
. = ASSERT (( __tdata_load_end__ <= __storage_flash_start__),
error: section .tdata overlaps...
Hi, I'm working on a project with the nRF52840 PCA10056 board. Using the IoT LwIP MQTT example, I can communicate with the insecure MQTT. However, I need to provide security...
