Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
Hi,
I am trying to communicate with a Wi-Fi module external to nRF52840 via UART. I am using the nrf_serial_read() API. I have tried different values for UART baud rate...
Hello, I am trying to broadcast a data among 2 receivers with a special ACK payload. I transmit and gather ACK with one receiver properly yet m_nrf_esb_mainstate locks in...
Hi,
I am trying to use Segger embedded studio for my project,
I get these errors:
Building ‘ble_app_uart_c_pca10028_s130’ from solution ‘ble_app_uart_c_pca10028_s130...
hello,BPROT does not work normally when i am debugging BPROT.
when i set CONFIG0 bit2 to 1,that is NRF_BPROT->CONFIG0 = 0x00000004,then i want to erase block 2(start address...
I am having a hard time turning ON semihosting. Here's my setup:
- Debugging is done via Eclipse GDB SEGGER J-Link Debugging with the Enable Semihosting checked and console...
Hi all,
I have a problem. I add NUS to light switch proxy . But the first time, I use nRF_UART or nRF Mesh connect to my Dev Kit. Then, I disconnect , I see it run MESH_GATT_EVT_TYPE_DISCONNECTED...
Hi,
I'm trying to set up a custom project with all the mentioned components. I build the bootloader, I'm using the `s140_nrf52_6.0.0_softdevice.hex` for the softdevice and...
Hi,
When i tried the light switch example from the Mesh 2.0 source code, i got the error code NRF_FAULT_ID_SD_ASSERT. when it is doing the provision process.
The last...
hi Nordic Support Team,
One Of Client has a Machine with Bluetooth Sending some Data every 1min.
They want to capture this data and Send this data through Mesh. Is it...
Hello,
I am using sdk 12.2.2 and nrf52 customised development board. My challenge is as follows.
1) I am getting success in fds'_write function.
ret_code_t ret = fds_record_write...
We planing to use the NFR52832 with heavy algorithm (Real time ECG analysis) with light BLE use. Does the BLE have higher priority that can slows the algorithm?
I have a wireless project. Requirements as:
Support platforms: Desktop/Laptop and mobile, Pc/Mac/IOS/Android. etc.
many connections: flexible but can support 100+...
Hi,
The problem is that after the initialization process the node does not contain the proxy advertiment data "1828", so the entire long process of working with the mesh...
hello, everyone.
I have to immigrate from SDK14 to SDK15.
I have some inquiries my project ( I will configure Transmitter(Beacon) and Receiver)
First, I have configured...
Hi,
I'm trying to log data over a serial connection using the DK52.
The data is coming from a sensor at about 2KHz at a size of 30 bytes per sample, so 60KBps.
I've...
