I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hello,
I am working with nrf51822 and I want to send data over ble to an android application which requires pairing. I modified the ble_app_uart example to read the data...
Hi Nordic Forum!
We're currently tuning our antenna since we runed with some problems during our EMC testing.
In that regard, what is the impedance (both input and output...
Hi,
Is there no specific code of ble_app_uart_coexist meant for PCA 10056 and eventually s140?
Or will the same code work for the nRF52840 board?
I am using SES and...
I want to use the nordic USB peripheral drivers to allow for the initialization of multiple devices. The end result of the project will be to have a single nordic creating...
I am using the nRF52832 (on Rigado BMD-300 EVAL kit). I am using keil IDE and nRF GO to upload my compiled code to my device. I am using SKD 15.2.0. Using Windows 10.
...
i donot know why,because other board is ok.
i am using this project
\nRF52832 pack\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_uart_c...
I am migrating my project from SDK 15.0 to SDK 15.2. I was using CC310 to accelerate crypto in the bootloader.
While builiding the bootloader wit SDK 15.2, I got the error...
Hi team, Does the nordic chip receive a Bluetooth signal being communicated with a mouse, keyboard, cell phone, etc., and the sleep state (sd_app_evt_wait()) is canceled?...
Hi,
Can we use BLE 5 beacon with BLE 4 scanner?
As BLE 5 is long range which is my main concern. So, can I get that long range with BLE 4 scanner?
Thanks,
i have done the 10 dfu steps in DFU quick start guide when the boards are not far from each other it works but when i make them far a little
i mean one device in the area...
I am using a Sparkfun nRF52832 breakout. I was trying to install the Softdevice settings onto my Arduino IDE once I clicked on tools -> "nRF5 flash device " the blue ticking...
Current consumption of my code running RTC from LFCLK is ~2.5uA from the power profiler when I set the register values as. NRF_POWER->RAM[2].POWERCLR = 0x01; NRF_POWER->RAM...
Hi,
Currently evaluating SDK and have some issues, I would like to run some demos.
I believe I've managed to erase the "preconfigured" Firmware on the SDK, I have tried...
I am working on SDK-15.2, nRF52832 Dev board. My question is how to add write protected characteristic by KEY? Mean when we want to write something from peer device (smartphone...
